/*
 *  ECP5 PicoRV32 demo
 *
 *  Copyright (C) 2017  Claire Xenia Wolf <claire@yosyshq.com>
 *  Copyright (C) 2018  gatecat <gatecat@ds0.me>
 *
 *  Permission to use, copy, modify, and/or distribute this software for any
 *  purpose with or without fee is hereby granted, provided that the above
 *  copyright notice and this permission notice appear in all copies.
 *
 *  THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
 *  WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
 *  MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
 *  ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
 *  WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
 *  ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
 *  OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
 *
 */

`ifdef PICORV32_V
`error "attosoc.v must be read before picorv32.v!"
`endif

`define PICORV32_REGS picosoc_regs

module attosoc (
	input clk,
	output reg led
);

	reg [5:0] reset_cnt = 0;
	wire resetn = &reset_cnt;

	always @(posedge clk) begin
		reset_cnt <= reset_cnt + !resetn;
	end

	parameter integer MEM_WORDS = 256;
	parameter [31:0] STACKADDR = (4*MEM_WORDS);       // end of memory
	parameter [31:0] PROGADDR_RESET = 32'h 0000_0000; // ROM at 0x0
	parameter integer ROM_BYTES = 256;

	reg [7:0] rom [0:ROM_BYTES-1];
	wire [31:0] rom_rdata = {rom[mem_addr+3], rom[mem_addr+2], rom[mem_addr+1], rom[mem_addr+0]};
	initial $readmemh("firmware.hex", rom);

	wire mem_valid;
	wire mem_instr;
	wire mem_ready;
	wire [31:0] mem_addr;
	wire [31:0] mem_wdata;
	wire [3:0] mem_wstrb;
	wire [31:0] mem_rdata;

    wire rom_ready = mem_valid && mem_addr[31:24] == 8'h00;

	wire iomem_valid;
	wire iomem_ready;
	wire [31:0] iomem_addr;
	wire [31:0] iomem_wdata;
	wire [3:0] iomem_wstrb;
	wire [31:0] iomem_rdata;

	assign iomem_valid = mem_valid && (mem_addr[31:24] > 8'h 01);
	assign iomem_ready = 1'b1;
	assign iomem_wstrb = mem_wstrb;
	assign iomem_addr = mem_addr;
	assign iomem_wdata = mem_wdata;

	wire [31:0] spimemio_cfgreg_do;


    always @(posedge clk)
        if (iomem_valid && iomem_wstrb[0])
            led <= iomem_wdata[0];

	assign mem_ready = (iomem_valid && iomem_ready) || rom_ready;

	assign mem_rdata = rom_rdata;

	picorv32 #(
		.STACKADDR(STACKADDR),
		.PROGADDR_RESET(PROGADDR_RESET),
		.PROGADDR_IRQ(32'h 0000_0000),
		.BARREL_SHIFTER(0),
		.COMPRESSED_ISA(0),
		.ENABLE_MUL(0),
		.ENABLE_DIV(0),
		.ENABLE_IRQ(0),
		.ENABLE_IRQ_QREGS(0)
	) cpu (
		.clk         (clk        ),
		.resetn      (resetn     ),
		.mem_valid   (mem_valid  ),
		.mem_instr   (mem_instr  ),
		.mem_ready   (mem_ready  ),
		.mem_addr    (mem_addr   ),
		.mem_wdata   (mem_wdata  ),
		.mem_wstrb   (mem_wstrb  ),
		.mem_rdata   (mem_rdata  )
	);


endmodule

// Implementation note:
// Replace the following two modules with wrappers for your SRAM cells.

module picosoc_regs (
	input clk, wen,
	input [5:0] waddr,
	input [5:0] raddr1,
	input [5:0] raddr2,
	input [31:0] wdata,
	output [31:0] rdata1,
	output [31:0] rdata2
);
	reg [31:0] regs [0:31];

	always @(posedge clk)
		if (wen) regs[waddr[4:0]] <= wdata;

	assign rdata1 = regs[raddr1[4:0]];
	assign rdata2 = regs[raddr2[4:0]];
endmodule