<!-- VPR Architecture Specification File --><!-- Quick XML Primer:
    * Data is hierarchical and composed of tags (similar to HTML)
    * All tags must be of the form <foo>content</foo> OR <foo /> with the latter form indicating no content. Don't forget the slash at the end.
    * Inside a start tag you may specify attributes in the form key="value". Refer to manual for the valid attributes for each element.
    * Comments may be included anywhere in the document except inside a tag where it's attribute list is defined.
    * Comments may contain any characters except two dashes. 
--><!-- Architecture based off Stratix IV
    Use closest ifar architecture: K06 N10 45nm fc 0.15 area-delay optimized, scale to 40 nm using linear scaling
    n10k06l04.fc15.area1delay1.cmos45nm.bptm.cmos45nm.xml
    * because documentation sparser for soft logic (delays not in QUIP), harder to track down, not worth our time considering the level of accuracy is approximate
      * delays multiplied by 40/45 to normalize for process difference between stratix 4 and 45 nm technology (called full scaling)

      Use delay numbers off Altera device handbook:

      http://www.altera.com/literature/hb/stratix-iv/stx4_5v1.pdf
      http://www.altera.com/literature/hb/stratix-iv/stx4_siv51004.pdf
      http://www.altera.com/literature/hb/stratix-iv/stx4_siv51003.pdf
      multipliers at 600 MHz, no detail on 9x9 vs 36x36
      * datasheets unclear
        * claims 4 18x18 independant multipliers, following test indicates that this is not the case:
          created 4 18x18 mulitpliers, logiclocked them to a single DSP block, compile
          result - 2 18x18 multipliers got packed together, the other 2 got ejected out of the logiclock region without error
          conclusion - just take the 600 MHz as is, and Quartus II logiclock hasn't fixed the bug that I've seen it do to registers when I worked at Altera (ie. eject without warning)
      --><architecture>
  <!-- ODIN II specific config -->
  <models>
    <model name="multiply">
      <input_ports>
        <port name="a" combinational_sink_ports="out"/>
        <port name="b" combinational_sink_ports="out"/>
      </input_ports>
      <output_ports>
        <port name="out"/>
      </output_ports>
    </model>
    <model name="single_port_ram">
      <input_ports>
        <port name="we" clock="clk"/>
        <!-- control -->
        <port name="addr" clock="clk"/>
        <!-- address lines -->
        <port name="data" clock="clk"/>
        <!-- data lines can be broken down into smaller bit widths minimum size 1 -->
        <port name="clk" is_clock="1"/>
        <!-- memories are often clocked -->
      </input_ports>
      <output_ports>
        <port name="out" clock="clk"/>
        <!-- output can be broken down into smaller bit widths minimum size 1 -->
      </output_ports>
    </model>
    <model name="dual_port_ram">
      <input_ports>
        <port name="we1" clock="clk"/>
        <!-- write enable -->
        <port name="we2" clock="clk"/>
        <!-- write enable -->
        <port name="addr1" clock="clk"/>
        <!-- address lines -->
        <port name="addr2" clock="clk"/>
        <!-- address lines -->
        <port name="data1" clock="clk"/>
        <!-- data lines can be broken down into smaller bit widths minimum size 1 -->
        <port name="data2" clock="clk"/>
        <!-- data lines can be broken down into smaller bit widths minimum size 1 -->
        <port name="clk" is_clock="1"/>
        <!-- memories are often clocked -->
      </input_ports>
      <output_ports>
        <port name="out1" clock="clk"/>
        <!-- output can be broken down into smaller bit widths minimum size 1 -->
        <port name="out2" clock="clk"/>
        <!-- output can be broken down into smaller bit widths minimum size 1 -->
      </output_ports>
    </model>
  </models>
  <!-- ODIN II specific config ends -->
  <!-- Physical descriptions begin (area optimized for N8-K6-L4 -->
  <layout>
    <auto_layout aspect_ratio="1.0">
        <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
        <perimeter type="io" priority="100"/>
        <corners type="EMPTY" priority="101"/>
        <!--Fill with 'clb'-->
        <fill type="clb" priority="10"/>
        <!--Column of 'mult_36' with 'EMPTY' blocks wherever a 'mult_36' does not fit. Vertical offset by 1 for perimeter.-->
        <col type="mult_36" startx="4" starty="1" repeatx="8" priority="20"/>
        <col type="EMPTY" startx="4" repeatx="8" starty="1" priority="19"/>
        <!--Column of 'memory' with 'EMPTY' blocks wherever a 'memory' does not fit. Vertical offset by 1 for perimeter.-->
        <col type="memory" startx="2" starty="1" repeatx="8" priority="20"/>
        <col type="EMPTY" startx="2" repeatx="8" starty="1" priority="19"/>
        </auto_layout>
</layout>
  <device>
    <sizing R_minW_nmos="6065.520020" R_minW_pmos="18138.500000" ipin_mux_trans_size="1.222260"/>
    <timing C_ipin_cblock="0.000000e+00" T_ipin_cblock="7.247000e-11"/>
    <area grid_logic_tile_area="14813.392"/>
    <!--area is for soft logic only-->
    <chan_width_distr>
      <io width="1.000000"/>
      <x distr="uniform" peak="1.000000"/>
      <y distr="uniform" peak="1.000000"/>
    </chan_width_distr>
    <switch_block type="wilton" fs="3"/>
  </device>
  <switchlist>
    <switch type="mux" name="0" R="0.000000" Cin="0.000000e+00" Cout="0.000000e+00" Tdel="6.837e-11" mux_trans_size="2.630740" buf_size="27.645901"/>
  </switchlist>
  <segmentlist>
    <segment freq="1.000000" length="4" type="unidir" Rmetal="0.000000" Cmetal="0.000000e+00">
      <mux name="0"/>
      <sb type="pattern">1 1 1 1 1</sb>
      <cb type="pattern">1 1 1 1</cb>
    </segment>
  </segmentlist>
  <complexblocklist>
    <!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
    <pb_type name="io" capacity="8">
      <input name="outpad" num_pins="1"/>
      <output name="inpad" num_pins="1"/>
      <clock name="clock" num_pins="1"/>
      <!-- IOs can operate as either inputs or outputs -->
      <mode name="inpad">
        <pb_type name="inpad" blif_model=".input" num_pb="1">
          <output name="inpad" num_pins="1"/>
        </pb_type>
        <interconnect>
          <direct name="inpad" input="inpad.inpad" output="io.inpad">
            <delay_constant max="4.243e-11" in_port="inpad.inpad" out_port="io.inpad"/>
          </direct>
        </interconnect>
      </mode>
      <mode name="outpad">
        <pb_type name="outpad" blif_model=".output" num_pb="1">
          <input name="outpad" num_pins="1"/>
        </pb_type>
        <interconnect>
          <direct name="outpad" input="io.outpad" output="outpad.outpad">
            <delay_constant max="1.394e-11" in_port="io.outpad" out_port="outpad.outpad"/>
          </direct>
        </interconnect>
      </mode>
      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
      <!-- IOs go on the periphery of the FPGA, for consistency, 
           make it physically equivalent on all sides so that only one definition of I/Os is needed.
           If I do not make a physically equivalent definition, then I need to define 4 different I/Os, one for each side of the FPGA
       -->
      <pinlocations pattern="custom">
        <loc side="left">io.outpad io.inpad io.clock</loc>
        <loc side="top">io.outpad io.inpad io.clock</loc>
        <loc side="right">io.outpad io.inpad io.clock</loc>
        <loc side="bottom">io.outpad io.inpad io.clock</loc>
      </pinlocations>
      </pb_type>

    <pb_type name="clb">
      <input name="I" num_pins="33" equivalent="true"/> <!-- NOTE: Logically Equivalent -->
      <output name="O" num_pins="10" equivalent="true"/> <!-- NOTE: Logically Equivalent -->
      <clock name="clk" num_pins="1"/>
      <!-- Describe basic logic element -->
      <pb_type name="ble" num_pb="10">
        <input name="in" num_pins="6"/>
        <output name="out" num_pins="1"/>
        <clock name="clk" num_pins="1"/>
        <pb_type name="soft_logic" num_pb="1">
          <input name="in" num_pins="6"/>
          <output name="out" num_pins="1"/>
          <mode name="n1_lut6">
            <pb_type name="lut6" blif_model=".names" num_pb="1" class="lut">
              <input name="in" num_pins="6" port_class="lut_in"/>
              <output name="out" num_pins="1" port_class="lut_out"/>
              <!-- LUT timing using delay matrix -->
              <delay_matrix type="max" in_port="lut6.in" out_port="lut6.out">
                          2.690e-10
                          2.690e-10
                          2.690e-10
                          2.690e-10
                          2.690e-10
                          2.690e-10
              </delay_matrix>
            </pb_type>
            <interconnect>
              <direct name="direct1" input="soft_logic.in[5:0]" output="lut6[0:0].in[5:0]"/>
              <direct name="direct2" input="lut6[0:0].out" output="soft_logic.out[0:0]"/>
            </interconnect>
          </mode>
        </pb_type>
        <pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
          <input name="D" num_pins="1" port_class="D"/>
          <output name="Q" num_pins="1" port_class="Q"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="ff.D" clock="clk"/>
          <T_clock_to_Q max="7.732e-11" port="ff.Q" clock="clk"/>
        </pb_type>
        <interconnect>
          <!-- Two ff, make ff available to only corresponding luts -->
          <direct name="direct1" input="ble.in" output="soft_logic.in"/>
          <direct name="direct2" input="soft_logic.out" output="ff.D"/>
          <direct name="direct4" input="ble.clk" output="ff.clk"/>
          <mux name="mux1" input="ff.Q soft_logic.out" output="ble.out"/>
        </interconnect>
      </pb_type>
      <interconnect>
        <complete name="crossbar" input="clb.I ble[9:0].out" output="ble[9:0].in">
          <delay_constant max="8.044000e-11" in_port="clb.I" out_port="ble[9:0].in"/>
          <delay_constant max="7.354000e-11" in_port="ble[9:0].out" out_port="ble[9:0].in"/>
        </complete>
        <complete name="clks" input="clb.clk" output="ble[9:0].clk"/>
        <direct name="clbouts" input="ble[9:0].out" output="clb.O"/>
      </interconnect>
      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
      <pinlocations pattern="spread"/>
      </pb_type>

    <!-- This is the 36*36 uniform mult -->
    <pb_type name="mult_36" height="4">
      <input name="a" num_pins="36"/>
      <input name="b" num_pins="36"/>
      <output name="out" num_pins="72"/>
      <mode name="two_divisible_mult_18x18">
        <pb_type name="divisible_mult_18x18" num_pb="2">
          <input name="a" num_pins="18"/>
          <input name="b" num_pins="18"/>
          <output name="out" num_pins="36"/>
          <mode name="two_mult_9x9">
            <pb_type name="mult_9x9_slice" num_pb="2">
              <input name="A_cfg" num_pins="9"/>
              <input name="B_cfg" num_pins="9"/>
              <output name="OUT_cfg" num_pins="18"/>
              <pb_type name="mult_9x9" blif_model=".subckt multiply" num_pb="1">
                <input name="a" num_pins="9"/>
                <input name="b" num_pins="9"/>
                <output name="out" num_pins="18"/>
                <delay_constant max="1.667e-9" in_port="mult_9x9.a" out_port="mult_9x9.out"/>
                <delay_constant max="1.667e-9" in_port="mult_9x9.b" out_port="mult_9x9.out"/>
              </pb_type>
              <interconnect>
                <direct name="a2a" input="mult_9x9_slice.A_cfg" output="mult_9x9.a"/>
                <direct name="b2b" input="mult_9x9_slice.B_cfg" output="mult_9x9.b"/>
                <direct name="out2out" input="mult_9x9.out" output="mult_9x9_slice.OUT_cfg"/>
              </interconnect>
            </pb_type>
            <interconnect>
              <direct name="a2a" input="divisible_mult_18x18.a" output="mult_9x9_slice[1:0].A_cfg"/>
              <direct name="b2b" input="divisible_mult_18x18.b" output="mult_9x9_slice[1:0].B_cfg"/>
              <direct name="out2out" input="mult_9x9_slice[1:0].OUT_cfg" output="divisible_mult_18x18.out"/>
            </interconnect>
          </mode>
          <mode name="mult_18x18">
            <pb_type name="mult_18x18_slice" num_pb="1">
              <input name="A_cfg" num_pins="18"/>
              <input name="B_cfg" num_pins="18"/>
              <output name="OUT_cfg" num_pins="36"/>
              <pb_type name="mult_18x18" blif_model=".subckt multiply" num_pb="1">
                <input name="a" num_pins="18"/>
                <input name="b" num_pins="18"/>
                <output name="out" num_pins="36"/>
                <delay_constant max="1.667e-9" in_port="mult_18x18.a" out_port="mult_18x18.out"/>
                <delay_constant max="1.667e-9" in_port="mult_18x18.b" out_port="mult_18x18.out"/>
              </pb_type>
              <interconnect>
                <direct name="a2a" input="mult_18x18_slice.A_cfg" output="mult_18x18.a"/>
                <direct name="b2b" input="mult_18x18_slice.B_cfg" output="mult_18x18.b"/>
                <direct name="out2out" input="mult_18x18.out" output="mult_18x18_slice.OUT_cfg"/>
              </interconnect>
            </pb_type>
            <interconnect>
              <direct name="a2a" input="divisible_mult_18x18.a" output="mult_18x18_slice.A_cfg"/>
              <direct name="b2b" input="divisible_mult_18x18.b" output="mult_18x18_slice.B_cfg"/>
              <direct name="out2out" input="mult_18x18_slice.OUT_cfg" output="divisible_mult_18x18.out"/>
            </interconnect>
          </mode>
        </pb_type>
        <interconnect>
          <direct name="a2a" input="mult_36.a" output="divisible_mult_18x18[1:0].a"/>
          <direct name="b2b" input="mult_36.b" output="divisible_mult_18x18[1:0].b"/>
          <direct name="out2out" input="divisible_mult_18x18[1:0].out" output="mult_36.out"/>
        </interconnect>
      </mode>
      <mode name="mult_36x36">
        <pb_type name="mult_36x36_slice" num_pb="1">
          <input name="A_cfg" num_pins="36"/>
          <input name="B_cfg" num_pins="36"/>
          <output name="OUT_cfg" num_pins="72"/>
          <pb_type name="mult_36x36" blif_model=".subckt multiply" num_pb="1">
            <input name="a" num_pins="36"/>
            <input name="b" num_pins="36"/>
            <output name="out" num_pins="72"/>
            <delay_constant max="1.667e-9" in_port="mult_36x36.a" out_port="mult_36x36.out"/>
            <delay_constant max="1.667e-9" in_port="mult_36x36.b" out_port="mult_36x36.out"/>
          </pb_type>
          <interconnect>
            <direct name="a2a" input="mult_36x36_slice.A_cfg" output="mult_36x36.a"/>
            <direct name="b2b" input="mult_36x36_slice.B_cfg" output="mult_36x36.b"/>
            <direct name="out2out" input="mult_36x36.out" output="mult_36x36_slice.OUT_cfg"/>
          </interconnect>
        </pb_type>
        <interconnect>
          <direct name="a2a" input="mult_36.a" output="mult_36x36_slice.A_cfg"/>
          <direct name="b2b" input="mult_36.b" output="mult_36x36_slice.B_cfg"/>
          <direct name="out2out" input="mult_36x36_slice.OUT_cfg" output="mult_36.out"/>
        </interconnect>
      </mode>
      <fc_in type="frac">0.15</fc_in>
      <fc_out type="frac">0.10</fc_out>
      <pinlocations pattern="spread"/>
      </pb_type>

    <!-- Memory based off Stratix IV 144K memory.  Setup time set to match flip-flop setup time at 45 nm. Clock to q based off 144K max MHz  -->
    <pb_type name="memory" height="6">
      <input name="addr1" num_pins="17"/>
      <input name="addr2" num_pins="17"/>
      <input name="data" num_pins="72"/>
      <input name="we1" num_pins="1"/>
      <input name="we2" num_pins="1"/>
      <output name="out" num_pins="72"/>
      <clock name="clk" num_pins="1"/>
      <mode name="mem_2048x72_sp">
        <pb_type name="mem_2048x72_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
          <input name="addr" num_pins="11" port_class="address"/>
          <input name="data" num_pins="72" port_class="data_in"/>
          <input name="we" num_pins="1" port_class="write_en"/>
          <output name="out" num_pins="72" port_class="data_out"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_2048x72_sp.addr" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_2048x72_sp.data" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_2048x72_sp.we" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_2048x72_sp.out" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[10:0]" output="mem_2048x72_sp.addr"/>
          <direct name="data1" input="memory.data[71:0]" output="mem_2048x72_sp.data"/>
          <direct name="writeen1" input="memory.we1" output="mem_2048x72_sp.we"/>
          <direct name="dataout1" input="mem_2048x72_sp.out" output="memory.out[71:0]"/>
          <direct name="clk" input="memory.clk" output="mem_2048x72_sp.clk"/>
        </interconnect>
      </mode>
      <mode name="mem_4096x36_dp">
        <pb_type name="mem_4096x36_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
          <input name="addr1" num_pins="12" port_class="address1"/>
          <input name="addr2" num_pins="12" port_class="address2"/>
          <input name="data1" num_pins="36" port_class="data_in1"/>
          <input name="data2" num_pins="36" port_class="data_in2"/>
          <input name="we1" num_pins="1" port_class="write_en1"/>
          <input name="we2" num_pins="1" port_class="write_en2"/>
          <output name="out1" num_pins="36" port_class="data_out1"/>
          <output name="out2" num_pins="36" port_class="data_out2"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_4096x36_dp.addr1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_dp.data1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_dp.we1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_dp.addr2" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_dp.data2" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_dp.we2" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_4096x36_dp.out1" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_4096x36_dp.out2" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[11:0]" output="mem_4096x36_dp.addr1"/>
          <direct name="address2" input="memory.addr2[11:0]" output="mem_4096x36_dp.addr2"/>
          <direct name="data1" input="memory.data[35:0]" output="mem_4096x36_dp.data1"/>
          <direct name="data2" input="memory.data[71:36]" output="mem_4096x36_dp.data2"/>
          <direct name="writeen1" input="memory.we1" output="mem_4096x36_dp.we1"/>
          <direct name="writeen2" input="memory.we2" output="mem_4096x36_dp.we2"/>
          <direct name="dataout1" input="mem_4096x36_dp.out1" output="memory.out[35:0]"/>
          <direct name="dataout2" input="mem_4096x36_dp.out2" output="memory.out[71:36]"/>
          <direct name="clk" input="memory.clk" output="mem_4096x36_dp.clk"/>
        </interconnect>
      </mode>
      <mode name="mem_4096x36_sp">
        <pb_type name="mem_4096x36_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
          <input name="addr" num_pins="12" port_class="address"/>
          <input name="data" num_pins="36" port_class="data_in"/>
          <input name="we" num_pins="1" port_class="write_en"/>
          <output name="out" num_pins="36" port_class="data_out"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_4096x36_sp.addr" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_sp.data" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_4096x36_sp.we" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_4096x36_sp.out" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[11:0]" output="mem_4096x36_sp.addr"/>
          <direct name="data1" input="memory.data[35:0]" output="mem_4096x36_sp.data"/>
          <direct name="writeen1" input="memory.we1" output="mem_4096x36_sp.we"/>
          <direct name="dataout1" input="mem_4096x36_sp.out" output="memory.out[35:0]"/>
          <direct name="clk" input="memory.clk" output="mem_4096x36_sp.clk"/>
        </interconnect>
      </mode>
      <mode name="mem_9182x18_dp">
        <pb_type name="mem_9182x18_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
          <input name="addr1" num_pins="13" port_class="address1"/>
          <input name="addr2" num_pins="13" port_class="address2"/>
          <input name="data1" num_pins="18" port_class="data_in1"/>
          <input name="data2" num_pins="18" port_class="data_in2"/>
          <input name="we1" num_pins="1" port_class="write_en1"/>
          <input name="we2" num_pins="1" port_class="write_en2"/>
          <output name="out1" num_pins="18" port_class="data_out1"/>
          <output name="out2" num_pins="18" port_class="data_out2"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_9182x18_dp.addr1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_dp.data1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_dp.we1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_dp.addr2" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_dp.data2" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_dp.we2" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_9182x18_dp.out1" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_9182x18_dp.out2" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[12:0]" output="mem_9182x18_dp.addr1"/>
          <direct name="address2" input="memory.addr2[12:0]" output="mem_9182x18_dp.addr2"/>
          <direct name="data1" input="memory.data[17:0]" output="mem_9182x18_dp.data1"/>
          <direct name="data2" input="memory.data[35:18]" output="mem_9182x18_dp.data2"/>
          <direct name="writeen1" input="memory.we1" output="mem_9182x18_dp.we1"/>
          <direct name="writeen2" input="memory.we2" output="mem_9182x18_dp.we2"/>
          <direct name="dataout1" input="mem_9182x18_dp.out1" output="memory.out[17:0]"/>
          <direct name="dataout2" input="mem_9182x18_dp.out2" output="memory.out[35:18]"/>
          <direct name="clk" input="memory.clk" output="mem_9182x18_dp.clk"/>
        </interconnect>
      </mode>
      <mode name="mem_9182x18_sp">
        <pb_type name="mem_9182x18_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
          <input name="addr" num_pins="13" port_class="address"/>
          <input name="data" num_pins="18" port_class="data_in"/>
          <input name="we" num_pins="1" port_class="write_en"/>
          <output name="out" num_pins="18" port_class="data_out"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_9182x18_sp.addr" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_sp.data" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_9182x18_sp.we" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_9182x18_sp.out" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[12:0]" output="mem_9182x18_sp.addr"/>
          <direct name="data1" input="memory.data[17:0]" output="mem_9182x18_sp.data"/>
          <direct name="writeen1" input="memory.we1" output="mem_9182x18_sp.we"/>
          <direct name="dataout1" input="mem_9182x18_sp.out" output="memory.out[17:0]"/>
          <direct name="clk" input="memory.clk" output="mem_9182x18_sp.clk"/>
        </interconnect>
      </mode>
      <mode name="mem_18194x9_dp">
        <pb_type name="mem_18194x9_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
          <input name="addr1" num_pins="14" port_class="address1"/>
          <input name="addr2" num_pins="14" port_class="address2"/>
          <input name="data1" num_pins="9" port_class="data_in1"/>
          <input name="data2" num_pins="9" port_class="data_in2"/>
          <input name="we1" num_pins="1" port_class="write_en1"/>
          <input name="we2" num_pins="1" port_class="write_en2"/>
          <output name="out1" num_pins="9" port_class="data_out1"/>
          <output name="out2" num_pins="9" port_class="data_out2"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_18194x9_dp.addr1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_dp.data1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_dp.we1" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_dp.addr2" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_dp.data2" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_dp.we2" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_18194x9_dp.out1" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_18194x9_dp.out2" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[13:0]" output="mem_18194x9_dp.addr1"/>
          <direct name="address2" input="memory.addr2[13:0]" output="mem_18194x9_dp.addr2"/>
          <direct name="data1" input="memory.data[8:0]" output="mem_18194x9_dp.data1"/>
          <direct name="data2" input="memory.data[17:9]" output="mem_18194x9_dp.data2"/>
          <direct name="writeen1" input="memory.we1" output="mem_18194x9_dp.we1"/>
          <direct name="writeen2" input="memory.we2" output="mem_18194x9_dp.we2"/>
          <direct name="dataout1" input="mem_18194x9_dp.out1" output="memory.out[8:0]"/>
          <direct name="dataout2" input="mem_18194x9_dp.out2" output="memory.out[17:9]"/>
          <direct name="clk" input="memory.clk" output="mem_18194x9_dp.clk"/>
        </interconnect>
      </mode>
      <mode name="mem_18194x9_sp">
        <pb_type name="mem_18194x9_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
          <input name="addr" num_pins="14" port_class="address"/>
          <input name="data" num_pins="9" port_class="data_in"/>
          <input name="we" num_pins="1" port_class="write_en"/>
          <output name="out" num_pins="9" port_class="data_out"/>
          <clock name="clk" num_pins="1" port_class="clock"/>
          <T_setup value="2.448e-10" port="mem_18194x9_sp.addr" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_sp.data" clock="clk"/>
          <T_setup value="2.448e-10" port="mem_18194x9_sp.we" clock="clk"/>
          <T_clock_to_Q max="1.852e-9" port="mem_18194x9_sp.out" clock="clk"/>
        </pb_type>
        <interconnect>
          <direct name="address1" input="memory.addr1[13:0]" output="mem_18194x9_sp.addr"/>
          <direct name="data1" input="memory.data[8:0]" output="mem_18194x9_sp.data"/>
          <direct name="writeen1" input="memory.we1" output="mem_18194x9_sp.we"/>
          <direct name="dataout1" input="mem_18194x9_sp.out" output="memory.out[8:0]"/>
          <direct name="clk" input="memory.clk" output="mem_18194x9_sp.clk"/>
        </interconnect>
      </mode>
      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
      <pinlocations pattern="spread"/>
      </pb_type>
  </complexblocklist>
</architecture>