read_verilog <<EOT
(* techmap_celltype = "$_DFF_P_" *)
module ffmap(...);
input D;
input C;
output Q;
parameter [0:0] _TECHMAP_WIREINIT_Q_ = 1'bx;

ffbb #(.INIT(_TECHMAP_WIREINIT_Q_)) _TECHMAP_REPLACE_(.D(D), .Q(Q), .C(C));

wire _TECHMAP_FAIL_ = _TECHMAP_WIREINIT_Q_ === 1'b1;

wire _TECHMAP_REMOVEINIT_Q_ = 1'b1;

endmodule
EOT
design -stash map

read_verilog <<EOT
(* techmap_celltype = "$_DFF_P_" *)
module ffmap(...);
input D;
input C;
output Q;
parameter [0:0] _TECHMAP_WIREINIT_Q_ = 1'bx;

ffbb #(.INIT(_TECHMAP_WIREINIT_Q_)) _TECHMAP_REPLACE_(.D(D), .Q(Q), .C(C));

wire _TECHMAP_FAIL_ = _TECHMAP_WIREINIT_Q_ === 1'b1;

wire _TECHMAP_REMOVEINIT_Q_ = 1'b0;

endmodule
EOT
design -stash map_noremove

read_verilog <<EOT
module ffbb (...);
parameter [0:0] INIT = 1'bx;
input D, C;
output Q;
endmodule

module top(...);
input clk;
input d;
output reg q0 = 0;
output reg q1 = 1;
output reg qx;

always @(posedge clk) begin
	q0 <= d;
	q1 <= d;
	qx <= d;
end
endmodule
EOT

design -save ref

hierarchy -auto-top
proc
simplemap
techmap -map %map
clean
# Make sure the parameter was used properly.
select -assert-count 2 top/t:ffbb
select -set ff0 top/w:q0 %ci t:ffbb %i
select -set ffx top/w:qx %ci t:ffbb %i
select -assert-count 1 @ff0
select -assert-count 1 @ffx
select -assert-count 1 @ff0 r:INIT=1'b0 %i
select -assert-count 1 @ffx r:INIT=1'bx %i
select -assert-count 0 top/w:q1 %ci t:ffbb %i
# Make sure the init values are dropped from the wires iff mapping was performed.
select -assert-count 0 top/w:q0 a:init %i
select -assert-count 1 top/w:q1 a:init=1'b1 %i
select -assert-count 0 top/w:qx a:init %i

design -load ref
hierarchy -auto-top
proc
simplemap
techmap -map %map_noremove
clean
# Make sure the parameter was used properly.
select -assert-count 2 top/t:ffbb
select -set ff0 top/w:q0 %ci t:ffbb %i
select -set ffx top/w:qx %ci t:ffbb %i
select -assert-count 1 @ff0
select -assert-count 1 @ffx
select -assert-count 1 @ff0 r:INIT=1'b0 %i
select -assert-count 1 @ffx r:INIT=1'bx %i
select -assert-count 0 top/w:q1 %ci t:ffbb %i
# Make sure the init values are not dropped from the wires.
select -assert-count 1 top/w:q0 a:init=1'b0 %i
select -assert-count 1 top/w:q1 a:init=1'b1 %i
select -assert-count 0 top/w:qx a:init %i