// Copyright 2020-2022 F4PGA Authors
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
//
// SPDX-License-Identifier: Apache-2.0

`default_nettype none

(* abc9_flop, lib_whitebox *)
module sh_dff(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    input wire C
);
    parameter [0:0] INIT = 1'b0;
    initial Q = INIT;

    always @(posedge C)
            Q <= D;
endmodule

(* abc9_box, lib_blackbox *)
module adder_carry(
    output wire sumout,
    output wire cout,
    input wire p,
    input wire g,
    input wire cin
);
    assign sumout = p ^ cin;
    assign cout = p ? cin : g;

endmodule

(* abc9_box, lib_whitebox *)
module adder_lut5(
   output wire lut5_out,
   (* abc9_carry *)
   output wire cout,
   input wire [0:4] in,
   (* abc9_carry *)
   input wire cin
);
    parameter [0:15] LUT=0;
    parameter IN2_IS_CIN = 0;

    wire [0:4] li = (IN2_IS_CIN) ? {in[0], in[1], cin, in[3], in[4]} : {in[0], in[1], in[2], in[3],in[4]};

    // Output function
    wire [0:15] s1 = li[0] ?
        {LUT[0], LUT[2], LUT[4], LUT[6], LUT[8], LUT[10], LUT[12], LUT[14], LUT[16], LUT[18], LUT[20], LUT[22], LUT[24], LUT[26], LUT[28], LUT[30]}:
        {LUT[1], LUT[3], LUT[5], LUT[7], LUT[9], LUT[11], LUT[13], LUT[15], LUT[17], LUT[19], LUT[21], LUT[23], LUT[25], LUT[27], LUT[29], LUT[31]};

    wire [0:7] s2 = li[1] ? {s1[0], s1[2], s1[4], s1[6], s1[8], s1[10], s1[12], s1[14]} :
                            {s1[1], s1[3], s1[5], s1[7], s1[9], s1[11], s1[13], s1[15]};

    wire [0:3] s3 = li[2] ? {s2[0], s2[2], s2[4], s2[6]} : {s2[1], s2[3], s2[5], s2[7]};
    wire [0:1] s4 = li[3] ? {s3[0], s3[2]} : {s3[1], s3[3]};

    assign lut5_out = li[4] ? s4[0] : s4[1];

    // Carry out function
    assign cout = (s3[2]) ? cin : s3[3];

endmodule


(* abc9_lut=1, lib_whitebox *)
module frac_lut6(
    input wire [0:5] in,
    output wire [0:3] lut4_out,
    output wire [0:1] lut5_out,
    output wire lut6_out
);
    parameter [0:63] LUT = 0;
    // Effective LUT input
    wire [0:5] li = in;

    // Output function
    wire [0:31] s1 = li[0] ?
    {LUT[0] , LUT[2] , LUT[4] , LUT[6] , LUT[8] , LUT[10], LUT[12], LUT[14], 
     LUT[16], LUT[18], LUT[20], LUT[22], LUT[24], LUT[26], LUT[28], LUT[30],
     LUT[32], LUT[34], LUT[36], LUT[38], LUT[40], LUT[42], LUT[44], LUT[46],
     LUT[48], LUT[50], LUT[52], LUT[54], LUT[56], LUT[58], LUT[60], LUT[62]}:
    {LUT[1] , LUT[3] , LUT[5] , LUT[7] , LUT[9] , LUT[11], LUT[13], LUT[15], 
     LUT[17], LUT[19], LUT[21], LUT[23], LUT[25], LUT[27], LUT[29], LUT[31],
     LUT[33], LUT[35], LUT[37], LUT[39], LUT[41], LUT[43], LUT[45], LUT[47],
     LUT[49], LUT[51], LUT[53], LUT[55], LUT[57], LUT[59], LUT[61], LUT[63]};

    wire [0:15] s2 = li[1] ?
    {s1[0] , s1[2] , s1[4] , s1[6] , s1[8] , s1[10], s1[12], s1[14],
     s1[16], s1[18], s1[20], s1[22], s1[24], s1[26], s1[28], s1[30]}:
    {s1[1] , s1[3] , s1[5] , s1[7] , s1[9] , s1[11], s1[13], s1[15],
     s1[17], s1[19], s1[21], s1[23], s1[25], s1[27], s1[29], s1[31]};

    wire [0:7] s3 = li[2] ?
    {s2[0], s2[2], s2[4], s2[6], s2[8], s2[10], s2[12], s2[14]}:
    {s2[1], s2[3], s2[5], s2[7], s2[9], s2[11], s2[13], s2[15]};

    wire [0:3] s4 = li[3] ? {s3[0], s3[2], s3[4], s3[6]}:
                            {s3[1], s3[3], s3[5], s3[7]};

    wire [0:1] s5 = li[4] ? {s4[0], s4[2]} : {s4[1], s4[3]};

    assign lut4_out[0] = s4[0];
    assign lut4_out[1] = s4[1];
    assign lut4_out[2] = s4[2];
    assign lut4_out[3] = s4[3];

    assign lut5_out[0] = s5[0];
    assign lut5_out[1] = s5[1];

    assign lut6_out = li[5] ? s5[0] : s5[1];

endmodule

(* abc9_flop, lib_whitebox *)
module dff(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    (* invertible_pin = "IS_C_INVERTED" *)
    input wire C
);
    parameter [0:0] INIT = 1'b0;
    parameter [0:0] IS_C_INVERTED = 1'b0;
    initial Q = INIT;
    case(|IS_C_INVERTED)
          1'b0:
            always @(posedge C)
                Q <= D;
          1'b1:
            always @(negedge C)
                Q <= D;
    endcase
endmodule

(* abc9_flop, lib_whitebox *)
module dffr(
    output reg Q,
    input wire D,
    input wire R,
    (* clkbuf_sink *)
    (* invertible_pin = "IS_C_INVERTED" *)
    input wire C
);
    parameter [0:0] INIT = 1'b0;
    parameter [0:0] IS_C_INVERTED = 1'b0;
    initial Q = INIT;
    case(|IS_C_INVERTED)
          1'b0:
            always @(posedge C or posedge R)
                if (R)
                        Q <= 1'b0;
                else
                        Q <= D;
          1'b1:
            always @(negedge C or posedge R)
                if (R)
                        Q <= 1'b0;
                else
                        Q <= D;
    endcase
endmodule

(* abc9_flop, lib_whitebox *)
module dffre(
    output reg Q,
    input wire D,
    input wire R,
    input wire E,
    (* clkbuf_sink *)
    (* invertible_pin = "IS_C_INVERTED" *)
    input wire C
);
    parameter [0:0] INIT = 1'b0;
    parameter [0:0] IS_C_INVERTED = 1'b0;
    initial Q = INIT;
    case(|IS_C_INVERTED)
          1'b0:
            always @(posedge C or posedge R)
              if (R)
                Q <= 1'b0;
              else if(E)
                Q <= D;
          1'b1:
            always @(negedge C or posedge R)
              if (R)
                Q <= 1'b0;
              else if(E)
                Q <= D;
        endcase
endmodule

module dffs(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    (* invertible_pin = "IS_C_INVERTED" *)
    input wire C,
    input wire S
);
    parameter [0:0] INIT = 1'b0;
    parameter [0:0] IS_C_INVERTED = 1'b0;
    initial Q = INIT;
    case(|IS_C_INVERTED)
          1'b0:
            always @(posedge C or negedge S)
              if (S)
                Q <= 1'b1;
              else
                Q <= D;
          1'b1:
            always @(negedge C or negedge S)
              if (S)
                Q <= 1'b1;
              else
                Q <= D;
        endcase
endmodule

module dffse(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    (* invertible_pin = "IS_C_INVERTED" *)
    input wire C,
    input wire S,
    input wire E
);
    parameter [0:0] INIT = 1'b0;
    parameter [0:0] IS_C_INVERTED = 1'b0;
    initial Q = INIT;
    case(|IS_C_INVERTED)
          1'b0:
            always @(posedge C or negedge S)
              if (S)
                Q <= 1'b1;
              else if(E)
                Q <= D;
          1'b1:
            always @(negedge C or negedge S)
              if (S)
                Q <= 1'b1;
              else if(E)
                Q <= D;
        endcase
endmodule

module dffsr(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    (* invertible_pin = "IS_C_INVERTED" *)
    input wire C,
    input wire R,
    input wire S
);
    parameter [0:0] INIT = 1'b0;
    parameter [0:0] IS_C_INVERTED = 1'b0;
    initial Q = INIT;
    case(|IS_C_INVERTED)
          1'b0:
            always @(posedge C or negedge S or negedge R)
              if (S)
                Q <= 1'b1;
              else if (R)
                Q <= 1'b0;
              else
                Q <= D;
          1'b1:
            always @(negedge C or negedge S or negedge R)
              if (S)
                Q <= 1'b1;
              else if (R)
                Q <= 1'b0;
              else
                Q <= D;
        endcase
endmodule

module dffsre(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    input wire C,
    input wire E,
    input wire R,
    input wire S
);
    parameter [0:0] INIT = 1'b0;
    initial Q = INIT;

        always @(posedge C or negedge S or negedge R)
          if (!R)
            Q <= 1'b0;
          else if (!S)
            Q <= 1'b1;
          else if (E)
            Q <= D;
        
endmodule

module dffnsre(
    output reg Q,
    input wire D,
    (* clkbuf_sink *)
    input wire C,
    input wire E,
    input wire R,
    input wire S
);
    parameter [0:0] INIT = 1'b0;
    initial Q = INIT;

        always @(negedge C or negedge S or negedge R)
          if (!R)
            Q <= 1'b0;
          else if (!S)
            Q <= 1'b1;
          else if (E)
            Q <= D;
        
endmodule

(* abc9_flop, lib_whitebox *)
module latchsre (
    output reg Q,
    input wire S,
    input wire R,
    input wire D,
    input wire G,
    input wire E
);
    parameter [0:0] INIT = 1'b0;
    initial Q = INIT;
    always @*
      begin
        if (!R) 
          Q <= 1'b0;
        else if (!S) 
          Q <= 1'b1;
        else if (E && G) 
          Q <= D;
      end
endmodule

(* abc9_flop, lib_whitebox *)
module latchnsre (
    output reg Q,
    input wire S,
    input wire R,
    input wire D,
    input wire G,
    input wire E
);
    parameter [0:0] INIT = 1'b0;
    initial Q = INIT;
    always @*
      begin
        if (!R) 
          Q <= 1'b0;
        else if (!S) 
          Q <= 1'b1;
        else if (E && !G) 
          Q <= D;
      end
endmodule

(* abc9_flop, lib_whitebox *)
module scff(
    output reg Q,
    input wire D,
    input wire clk
);
    parameter [0:0] INIT = 1'b0;
    initial Q = INIT;

    always @(posedge clk)
            Q <= D;
endmodule

module TDP_BRAM18 (
    (* clkbuf_sink *)
    input wire CLOCKA,
    (* clkbuf_sink *)
    input wire CLOCKB,
    input wire READENABLEA,
    input wire READENABLEB,
    input wire [13:0] ADDRA,
    input wire [13:0] ADDRB,
    input wire [15:0] WRITEDATAA,
    input wire [15:0] WRITEDATAB,
    input wire [1:0] WRITEDATAAP,
    input wire [1:0] WRITEDATABP,
    input wire WRITEENABLEA,
    input wire WRITEENABLEB,
    input wire [1:0] BYTEENABLEA,
    input wire [1:0] BYTEENABLEB,
    //input wire [2:0] WRITEDATAWIDTHA,
    //input wire [2:0] WRITEDATAWIDTHB,
    //input wire [2:0] READDATAWIDTHA,
    //input wire [2:0] READDATAWIDTHB,
    output wire [15:0] READDATAA,
    output wire [15:0] READDATAB,
    output wire [1:0] READDATAAP,
    output wire [1:0] READDATABP
);
    parameter INITP_00 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_01 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_02 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_03 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_04 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_05 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_06 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_07 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_00 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_01 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_02 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_03 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_04 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_05 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_06 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_07 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_08 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_09 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_10 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_11 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_12 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_13 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_14 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_15 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_16 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_17 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_18 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_19 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_20 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_21 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_22 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_23 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_24 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_25 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_26 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_27 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_28 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_29 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_30 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_31 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_32 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_33 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_34 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_35 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_36 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_37 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_38 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_39 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter integer READ_WIDTH_A = 0;
    parameter integer READ_WIDTH_B = 0;
    parameter integer WRITE_WIDTH_A = 0;
    parameter integer WRITE_WIDTH_B = 0;

endmodule

module TDP36K (
    RESET_ni,
    WEN_A1_i,
    WEN_B1_i,
    REN_A1_i,
    REN_B1_i,
    CLK_A1_i,
    CLK_B1_i,
    BE_A1_i,
    BE_B1_i,
    ADDR_A1_i,
    ADDR_B1_i,
    WDATA_A1_i,
    WDATA_B1_i,
    RDATA_A1_o,
    RDATA_B1_o,
    FLUSH1_i,
    WEN_A2_i,
    WEN_B2_i,
    REN_A2_i,
    REN_B2_i,
    CLK_A2_i,
    CLK_B2_i,
    BE_A2_i,
    BE_B2_i,
    ADDR_A2_i,
    ADDR_B2_i,
    WDATA_A2_i,
    WDATA_B2_i,
    RDATA_A2_o,
    RDATA_B2_o,
    FLUSH2_i
);
    parameter [80:0] MODE_BITS = 81'd0;

    // First 18K RAMFIFO (41 bits)
    localparam [ 0:0] SYNC_FIFO1_i  = MODE_BITS[0];
    localparam [ 2:0] RMODE_A1_i    = MODE_BITS[3 : 1];
    localparam [ 2:0] RMODE_B1_i    = MODE_BITS[6 : 4];
    localparam [ 2:0] WMODE_A1_i    = MODE_BITS[9 : 7];
    localparam [ 2:0] WMODE_B1_i    = MODE_BITS[12:10];
    localparam [ 0:0] FMODE1_i      = MODE_BITS[13];
    localparam [ 0:0] POWERDN1_i    = MODE_BITS[14];
    localparam [ 0:0] SLEEP1_i      = MODE_BITS[15];
    localparam [ 0:0] PROTECT1_i    = MODE_BITS[16];
    localparam [11:0] UPAE1_i       = MODE_BITS[28:17];
    localparam [11:0] UPAF1_i       = MODE_BITS[40:29];

    // Second 18K RAMFIFO (39 bits)
    localparam [ 0:0] SYNC_FIFO2_i  = MODE_BITS[41];
    localparam [ 2:0] RMODE_A2_i    = MODE_BITS[44:42];
    localparam [ 2:0] RMODE_B2_i    = MODE_BITS[47:45];
    localparam [ 2:0] WMODE_A2_i    = MODE_BITS[50:48];
    localparam [ 2:0] WMODE_B2_i    = MODE_BITS[53:51];
    localparam [ 0:0] FMODE2_i      = MODE_BITS[54];
    localparam [ 0:0] POWERDN2_i    = MODE_BITS[55];
    localparam [ 0:0] SLEEP2_i      = MODE_BITS[56];
    localparam [ 0:0] PROTECT2_i    = MODE_BITS[57];
    localparam [10:0] UPAE2_i       = MODE_BITS[68:58];
    localparam [10:0] UPAF2_i       = MODE_BITS[79:69];

    // Split (1 bit)
    localparam [ 0:0] SPLIT_i       = MODE_BITS[80];

    parameter INITP_00 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_01 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_02 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_03 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_04 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_05 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_06 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_07 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_08 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_09 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_0A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_0B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_0C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_0D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_0E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INITP_0F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_00 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_01 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_02 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_03 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_04 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_05 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_06 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_07 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_08 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_09 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_0F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_10 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_11 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_12 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_13 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_14 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_15 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_16 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_17 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_18 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_19 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_1F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_20 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_21 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_22 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_23 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_24 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_25 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_26 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_27 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_28 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_29 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_2F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_30 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_31 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_32 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_33 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_34 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_35 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_36 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_37 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_38 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_39 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_3F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_40 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_41 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_42 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_43 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_44 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_45 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_46 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_47 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_48 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_49 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_4A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_4B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_4C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_4D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_4E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_4F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_50 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_51 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_52 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_53 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_54 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_55 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_56 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_57 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_58 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_59 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_5A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_5B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_5C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_5D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_5E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_5F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_60 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_61 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_62 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_63 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_64 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_65 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_66 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_67 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_68 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_69 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_6A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_6B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_6C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_6D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_6E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_6F = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_70 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_71 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_72 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_73 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_74 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_75 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_76 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_77 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_78 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_79 = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_7A = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_7B = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_7C = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_7D = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_7E = 256'h0000000000000000000000000000000000000000000000000000000000000000;
    parameter INIT_7F = 256'h0000000000000000000000000000000000000000000000000000000000000000;

    input wire RESET_ni;
    input wire WEN_A1_i;
    input wire WEN_B1_i;
    input wire REN_A1_i;
    input wire REN_B1_i;
    (* clkbuf_sink *)
    input wire CLK_A1_i;
    (* clkbuf_sink *)
    input wire CLK_B1_i;
    input wire [1:0] BE_A1_i;
    input wire [1:0] BE_B1_i;
    input wire [14:0] ADDR_A1_i;
    input wire [14:0] ADDR_B1_i;
    input wire [17:0] WDATA_A1_i;
    input wire [17:0] WDATA_B1_i;
    output reg [17:0] RDATA_A1_o;
    output reg [17:0] RDATA_B1_o;
    input wire FLUSH1_i;
    input wire WEN_A2_i;
    input wire WEN_B2_i;
    input wire REN_A2_i;
    input wire REN_B2_i;
    (* clkbuf_sink *)
    input wire CLK_A2_i;
    (* clkbuf_sink *)
    input wire CLK_B2_i;
    input wire [1:0] BE_A2_i;
    input wire [1:0] BE_B2_i;
    input wire [13:0] ADDR_A2_i;
    input wire [13:0] ADDR_B2_i;
    input wire [17:0] WDATA_A2_i;
    input wire [17:0] WDATA_B2_i;
    output reg [17:0] RDATA_A2_o;
    output reg [17:0] RDATA_B2_o;
    input wire FLUSH2_i;
    wire EMPTY2;
    wire EPO2;
    wire EWM2;
    wire FULL2;
    wire FMO2;
    wire FWM2;
    wire EMPTY1;
    wire EPO1;
    wire EWM1;
    wire FULL1;
    wire FMO1;
    wire FWM1;
    wire UNDERRUN1;
    wire OVERRUN1;
    wire UNDERRUN2;
    wire OVERRUN2;
    wire UNDERRUN3;
    wire OVERRUN3;
    wire EMPTY3;
    wire EPO3;
    wire EWM3;
    wire FULL3;
    wire FMO3;
    wire FWM3;
    wire ram_fmode1;
    wire ram_fmode2;
    wire [17:0] ram_rdata_a1;
    wire [17:0] ram_rdata_b1;
    wire [17:0] ram_rdata_a2;
    wire [17:0] ram_rdata_b2;
    reg [17:0] ram_wdata_a1;
    reg [17:0] ram_wdata_b1;
    reg [17:0] ram_wdata_a2;
    reg [17:0] ram_wdata_b2;
    reg [14:0] laddr_a1;
    reg [14:0] laddr_b1;
    wire [13:0] ram_addr_a1;
    wire [13:0] ram_addr_b1;
    wire [13:0] ram_addr_a2;
    wire [13:0] ram_addr_b2;
    wire smux_clk_a1;
    wire smux_clk_b1;
    wire smux_clk_a2;
    wire smux_clk_b2;
    reg [1:0] ram_be_a1;
    reg [1:0] ram_be_a2;
    reg [1:0] ram_be_b1;
    reg [1:0] ram_be_b2;
    wire [2:0] ram_rmode_a1;
    wire [2:0] ram_wmode_a1;
    wire [2:0] ram_rmode_b1;
    wire [2:0] ram_wmode_b1;
    wire [2:0] ram_rmode_a2;
    wire [2:0] ram_wmode_a2;
    wire [2:0] ram_rmode_b2;
    wire [2:0] ram_wmode_b2;
    wire ram_ren_a1;
    wire ram_ren_b1;
    wire ram_ren_a2;
    wire ram_ren_b2;
    wire ram_wen_a1;
    wire ram_wen_b1;
    wire ram_wen_a2;
    wire ram_wen_b2;
    wire ren_o;
    wire [11:0] ff_raddr;
    wire [11:0] ff_waddr;
    reg [35:0] fifo_rdata;
    wire [1:0] fifo_rmode;
    wire [1:0] fifo_wmode;
    wire [1:0] bwl;
    wire [17:0] pl_dout0;
    wire [17:0] pl_dout1;
    wire sclk_a1;
    wire sclk_b1;
    wire sclk_a2;
    wire sclk_b2;
    wire sreset;
    wire flush1;
    wire flush2;
    assign sreset = RESET_ni;
    assign flush1 = ~FLUSH1_i;
    assign flush2 = ~FLUSH2_i;
    assign ram_fmode1 = FMODE1_i & SPLIT_i;
    assign ram_fmode2 = FMODE2_i & SPLIT_i;
    assign smux_clk_a1 = CLK_A1_i;
    assign smux_clk_b1 = (FMODE1_i ? (SYNC_FIFO1_i ? CLK_A1_i : CLK_B1_i) : CLK_B1_i);
    assign smux_clk_a2 = (SPLIT_i ? CLK_A2_i : CLK_A1_i);
    assign smux_clk_b2 = (SPLIT_i ? (FMODE2_i ? (SYNC_FIFO2_i ? CLK_A2_i : CLK_B2_i) : CLK_B2_i) : (FMODE1_i ? (SYNC_FIFO1_i ? CLK_A1_i : CLK_B1_i) : CLK_B1_i));
    assign sclk_a1 = smux_clk_a1;
    assign sclk_a2 = smux_clk_a2;
    assign sclk_b1 = smux_clk_b1;
    assign sclk_b2 = smux_clk_b2;
    assign ram_ren_a1 = (SPLIT_i ? REN_A1_i : (FMODE1_i ? 0 : REN_A1_i));
    assign ram_ren_a2 = (SPLIT_i ? REN_A2_i : (FMODE1_i ? 0 : REN_A1_i));
    assign ram_ren_b1 = (SPLIT_i ? REN_B1_i : (FMODE1_i ? ren_o : REN_B1_i));
    assign ram_ren_b2 = (SPLIT_i ? REN_B2_i : (FMODE1_i ? ren_o : REN_B1_i));
    localparam MODE_36 = 3'b011;
    assign ram_wen_a1 = (SPLIT_i ? WEN_A1_i : (FMODE1_i ? ~FULL3 & WEN_A1_i : (WMODE_A1_i == MODE_36 ? WEN_A1_i : WEN_A1_i & ~ADDR_A1_i[4])));
    assign ram_wen_a2 = (SPLIT_i ? WEN_A2_i : (FMODE1_i ? ~FULL3 & WEN_A1_i : (WMODE_A1_i == MODE_36 ? WEN_A1_i : WEN_A1_i & ADDR_A1_i[4])));
    assign ram_wen_b1 = (SPLIT_i ? WEN_B1_i : (WMODE_B1_i == MODE_36 ? WEN_B1_i : WEN_B1_i & ~ADDR_B1_i[4]));
    assign ram_wen_b2 = (SPLIT_i ? WEN_B2_i : (WMODE_B1_i == MODE_36 ? WEN_B1_i : WEN_B1_i & ADDR_B1_i[4]));
    assign ram_addr_a1 = (SPLIT_i ? ADDR_A1_i[13:0] : (FMODE1_i ? {ff_waddr[11:2], ff_waddr[0], 3'b000} : {ADDR_A1_i[14:5], ADDR_A1_i[3:0]}));
    assign ram_addr_b1 = (SPLIT_i ? ADDR_B1_i[13:0] : (FMODE1_i ? {ff_raddr[11:2], ff_raddr[0], 3'b000} : {ADDR_B1_i[14:5], ADDR_B1_i[3:0]}));
    assign ram_addr_a2 = (SPLIT_i ? ADDR_A2_i[13:0] : (FMODE1_i ? {ff_waddr[11:2], ff_waddr[0], 3'b000} : {ADDR_A1_i[14:5], ADDR_A1_i[3:0]}));
    assign ram_addr_b2 = (SPLIT_i ? ADDR_B2_i[13:0] : (FMODE1_i ? {ff_raddr[11:2], ff_raddr[0], 3'b000} : {ADDR_B1_i[14:5], ADDR_B1_i[3:0]}));
    assign bwl = (SPLIT_i ? ADDR_A1_i[4:3] : (FMODE1_i ? ff_waddr[1:0] : ADDR_A1_i[4:3]));
    localparam MODE_18 = 3'b010;
    localparam MODE_9 = 3'b001;
    always @(*) begin : WDATA_SEL
        case (SPLIT_i)
            1: begin
                ram_wdata_a1 = WDATA_A1_i;
                ram_wdata_a2 = WDATA_A2_i;
                ram_wdata_b1 = WDATA_B1_i;
                ram_wdata_b2 = WDATA_B2_i;
                ram_be_a2 = BE_A2_i;
                ram_be_b2 = BE_B2_i;
                ram_be_a1 = BE_A1_i;
                ram_be_b1 = BE_B1_i;
            end
            0: begin
                case (WMODE_A1_i)
                    MODE_36: begin
                        ram_wdata_a1 = WDATA_A1_i;
                        ram_wdata_a2 = WDATA_A2_i;
                        ram_be_a2 = (FMODE1_i ? 2'b11 : BE_A2_i);
                        ram_be_a1 = (FMODE1_i ? 2'b11 : BE_A1_i);
                    end
                    MODE_18: begin
                        ram_wdata_a1 = WDATA_A1_i;
                        ram_wdata_a2 = WDATA_A1_i;
                        ram_be_a1 = (FMODE1_i ? (ff_waddr[1] ? 2'b00 : 2'b11) : BE_A1_i);
                        ram_be_a2 = (FMODE1_i ? (ff_waddr[1] ? 2'b11 : 2'b00) : BE_A1_i);
                    end
                    MODE_9: begin
                        ram_wdata_a1[7:0] = WDATA_A1_i[7:0];
                        ram_wdata_a1[16] = WDATA_A1_i[16];
                        ram_wdata_a1[15:8] = WDATA_A1_i[7:0];
                        ram_wdata_a1[17] = WDATA_A1_i[16];
                        ram_wdata_a2[7:0] = WDATA_A1_i[7:0];
                        ram_wdata_a2[16] = WDATA_A1_i[16];
                        ram_wdata_a2[15:8] = WDATA_A1_i[7:0];
                        ram_wdata_a2[17] = WDATA_A1_i[16];
                        case (bwl)
                            0: {ram_be_a2, ram_be_a1} = 4'b0001;
                            1: {ram_be_a2, ram_be_a1} = 4'b0010;
                            2: {ram_be_a2, ram_be_a1} = 4'b0100;
                            3: {ram_be_a2, ram_be_a1} = 4'b1000;
                        endcase
                    end
                    default: begin
                        ram_wdata_a1 = WDATA_A1_i;
                        ram_wdata_a2 = WDATA_A1_i;
                        ram_be_a2 = (FMODE1_i ? 2'b11 : BE_A1_i);
                        ram_be_a1 = (FMODE1_i ? 2'b11 : BE_A1_i);
                    end
                endcase
                case (WMODE_B1_i)
                    MODE_36: begin
                        ram_wdata_b1 = (FMODE1_i ? 18'b000000000000000000 : WDATA_B1_i);
                        ram_wdata_b2 = (FMODE1_i ? 18'b000000000000000000 : WDATA_B2_i);
                        ram_be_b2 = BE_B2_i;
                        ram_be_b1 = BE_B1_i;
                    end
                    MODE_18: begin
                        ram_wdata_b1 = (FMODE1_i ? 18'b000000000000000000 : WDATA_B1_i);
                        ram_wdata_b2 = (FMODE1_i ? 18'b000000000000000000 : WDATA_B1_i);
                        ram_be_b1 = BE_B1_i;
                        ram_be_b2 = BE_B1_i;
                    end
                    MODE_9: begin
                        ram_wdata_b1[7:0] = WDATA_B1_i[7:0];
                        ram_wdata_b1[16] = WDATA_B1_i[16];
                        ram_wdata_b1[15:8] = WDATA_B1_i[7:0];
                        ram_wdata_b1[17] = WDATA_B1_i[16];
                        ram_wdata_b2[7:0] = WDATA_B1_i[7:0];
                        ram_wdata_b2[16] = WDATA_B1_i[16];
                        ram_wdata_b2[15:8] = WDATA_B1_i[7:0];
                        ram_wdata_b2[17] = WDATA_B1_i[16];
                        case (ADDR_B1_i[4:3])
                            0: {ram_be_b2, ram_be_b1} = 4'b0001;
                            1: {ram_be_b2, ram_be_b1} = 4'b0010;
                            2: {ram_be_b2, ram_be_b1} = 4'b0100;
                            3: {ram_be_b2, ram_be_b1} = 4'b1000;
                        endcase
                    end
                    default: begin
                        ram_wdata_b1 = (FMODE1_i ? 18'b000000000000000000 : WDATA_B1_i);
                        ram_wdata_b2 = (FMODE1_i ? 18'b000000000000000000 : WDATA_B1_i);
                        ram_be_b2 = BE_B1_i;
                        ram_be_b1 = BE_B1_i;
                    end
                endcase
            end
        endcase
    end
    assign ram_rmode_a1 = (SPLIT_i ? (RMODE_A1_i == MODE_36 ? MODE_18 : RMODE_A1_i) : (RMODE_A1_i == MODE_36 ? MODE_18 : RMODE_A1_i));
    assign ram_rmode_a2 = (SPLIT_i ? (RMODE_A2_i == MODE_36 ? MODE_18 : RMODE_A2_i) : (RMODE_A1_i == MODE_36 ? MODE_18 : RMODE_A1_i));
    assign ram_wmode_a1 = (SPLIT_i ? (WMODE_A1_i == MODE_36 ? MODE_18 : WMODE_A1_i) : (WMODE_A1_i == MODE_36 ? MODE_18 : (FMODE1_i ? MODE_18 : WMODE_A1_i)));
    assign ram_wmode_a2 = (SPLIT_i ? (WMODE_A2_i == MODE_36 ? MODE_18 : WMODE_A2_i) : (WMODE_A1_i == MODE_36 ? MODE_18 : (FMODE1_i ? MODE_18 : WMODE_A1_i)));
    assign ram_rmode_b1 = (SPLIT_i ? (RMODE_B1_i == MODE_36 ? MODE_18 : RMODE_B1_i) : (RMODE_B1_i == MODE_36 ? MODE_18 : (FMODE1_i ? MODE_18 : RMODE_B1_i)));
    assign ram_rmode_b2 = (SPLIT_i ? (RMODE_B2_i == MODE_36 ? MODE_18 : RMODE_B2_i) : (RMODE_B1_i == MODE_36 ? MODE_18 : (FMODE1_i ? MODE_18 : RMODE_B1_i)));
    assign ram_wmode_b1 = (SPLIT_i ? (WMODE_B1_i == MODE_36 ? MODE_18 : WMODE_B1_i) : (WMODE_B1_i == MODE_36 ? MODE_18 : WMODE_B1_i));
    assign ram_wmode_b2 = (SPLIT_i ? (WMODE_B2_i == MODE_36 ? MODE_18 : WMODE_B2_i) : (WMODE_B1_i == MODE_36 ? MODE_18 : WMODE_B1_i));
    always @(*) begin : FIFO_READ_SEL
        case (RMODE_B1_i)
            MODE_36: fifo_rdata = {ram_rdata_b2[17:16], ram_rdata_b1[17:16], ram_rdata_b2[15:0], ram_rdata_b1[15:0]};
            MODE_18: fifo_rdata = (ff_raddr[1] ? {18'b000000000000000000, ram_rdata_b2} : {18'b000000000000000000, ram_rdata_b1});
            MODE_9:
                case (ff_raddr[1:0])
                    0: fifo_rdata = {19'b0000000000000000000, ram_rdata_b1[16], 8'b00000000, ram_rdata_b1[7:0]};
                    1: fifo_rdata = {19'b0000000000000000000, ram_rdata_b1[17], 8'b00000000, ram_rdata_b1[15:8]};
                    2: fifo_rdata = {19'b0000000000000000000, ram_rdata_b2[16], 8'b00000000, ram_rdata_b2[7:0]};
                    3: fifo_rdata = {19'b0000000000000000000, ram_rdata_b2[17], 8'b00000000, ram_rdata_b2[15:8]};
                endcase
            default: fifo_rdata = {ram_rdata_b2, ram_rdata_b1};
        endcase
    end
    localparam MODE_1 = 3'b101;
    localparam MODE_2 = 3'b110;
    localparam MODE_4 = 3'b100;
    always @(*) begin : RDATA_SEL
        case (SPLIT_i)
            1: begin
                RDATA_A1_o = (FMODE1_i ? {10'b0000000000, EMPTY1, EPO1, EWM1, UNDERRUN1, FULL1, FMO1, FWM1, OVERRUN1} : ram_rdata_a1);
                RDATA_B1_o = ram_rdata_b1;
                RDATA_A2_o = (FMODE2_i ? {10'b0000000000, EMPTY2, EPO2, EWM2, UNDERRUN2, FULL2, FMO2, FWM2, OVERRUN2} : ram_rdata_a2);
                RDATA_B2_o = ram_rdata_b2;
            end
            0: begin
                if (FMODE1_i) begin
                    RDATA_A1_o = {10'b0000000000, EMPTY3, EPO3, EWM3, UNDERRUN3, FULL3, FMO3, FWM3, OVERRUN3};
                    RDATA_A2_o = 18'b000000000000000000;
                end
                else
                    case (RMODE_A1_i)
                        MODE_36: begin
                            RDATA_A1_o = {ram_rdata_a1[17:0]};
                            RDATA_A2_o = {ram_rdata_a2[17:0]};
                        end
                        MODE_18: begin
                            RDATA_A1_o = (laddr_a1[4] ? ram_rdata_a2 : ram_rdata_a1);
                            RDATA_A2_o = 18'b000000000000000000;
                        end
                        MODE_9: begin
                            RDATA_A1_o = (laddr_a1[4] ? {{2 {ram_rdata_a2[16]}}, {2 {ram_rdata_a2[7:0]}}} : {{2 {ram_rdata_a1[16]}}, {2 {ram_rdata_a1[7:0]}}});
                            RDATA_A2_o = 18'b000000000000000000;
                        end
                        MODE_4: begin
                            RDATA_A2_o = 18'b000000000000000000;
                            RDATA_A1_o[17:4] = 14'b00000000000000;
                            RDATA_A1_o[3:0] = (laddr_a1[4] ? ram_rdata_a2[3:0] : ram_rdata_a1[3:0]);
                        end
                        MODE_2: begin
                            RDATA_A2_o = 18'b000000000000000000;
                            RDATA_A1_o[17:2] = 16'b0000000000000000;
                            RDATA_A1_o[1:0] = (laddr_a1[4] ? ram_rdata_a2[1:0] : ram_rdata_a1[1:0]);
                        end
                        MODE_1: begin
                            RDATA_A2_o = 18'b000000000000000000;
                            RDATA_A1_o[17:1] = 17'b00000000000000000;
                            RDATA_A1_o[0] = (laddr_a1[4] ? ram_rdata_a2[0] : ram_rdata_a1[0]);
                        end
                        default: begin
                            RDATA_A1_o = {ram_rdata_a2[1:0], ram_rdata_a1[15:0]};
                            RDATA_A2_o = {ram_rdata_a2[17:16], ram_rdata_a1[17:16], ram_rdata_a2[15:2]};
                        end
                    endcase
                case (RMODE_B1_i)
                    MODE_36: begin
                        RDATA_B1_o = {ram_rdata_b1};
                        RDATA_B2_o = {ram_rdata_b2};
                    end
                    MODE_18: begin
                        RDATA_B1_o = (FMODE1_i ? fifo_rdata[17:0] : (laddr_b1[4] ? ram_rdata_b2 : ram_rdata_b1));
                        RDATA_B2_o = 18'b000000000000000000;
                    end
                    MODE_9: begin
                        RDATA_B1_o = (FMODE1_i ? {fifo_rdata[17:0]} : (laddr_b1[4] ? {1'b0, ram_rdata_b2[16], 8'b00000000, ram_rdata_b2[7:0]} : {1'b0, ram_rdata_b1[16], 8'b00000000, ram_rdata_b1[7:0]}));
                        RDATA_B2_o = 18'b000000000000000000;
                    end
                    MODE_4: begin
                        RDATA_B2_o = 18'b000000000000000000;
                        RDATA_B1_o[17:4] = 14'b00000000000000;
                        RDATA_B1_o[3:0] = (laddr_b1[4] ? ram_rdata_b2[3:0] : ram_rdata_b1[3:0]);
                    end
                    MODE_2: begin
                        RDATA_B2_o = 18'b000000000000000000;
                        RDATA_B1_o[17:2] = 16'b0000000000000000;
                        RDATA_B1_o[1:0] = (laddr_b1[4] ? ram_rdata_b2[1:0] : ram_rdata_b1[1:0]);
                    end
                    MODE_1: begin
                        RDATA_B2_o = 18'b000000000000000000;
                        RDATA_B1_o[17:1] = 17'b00000000000000000;
                        RDATA_B1_o[0] = (laddr_b1[4] ? ram_rdata_b2[0] : ram_rdata_b1[0]);
                    end
                    default: begin
                        RDATA_B1_o = ram_rdata_b1;
                        RDATA_B2_o = ram_rdata_b2;
                    end
                endcase
            end
        endcase
    end
    always @(posedge sclk_a1 or negedge sreset)
        if (sreset == 0)
            laddr_a1 <= 1'sb0;
        else
            laddr_a1 <= ADDR_A1_i;
    always @(posedge sclk_b1 or negedge sreset)
        if (sreset == 0)
            laddr_b1 <= 1'sb0;
        else
            laddr_b1 <= ADDR_B1_i;
    assign fifo_wmode = ((WMODE_A1_i == MODE_36) ? 2'b00 : ((WMODE_A1_i == MODE_18) ? 2'b01 : ((WMODE_A1_i == MODE_9) ? 2'b10 : 2'b00)));
    assign fifo_rmode = ((RMODE_B1_i == MODE_36) ? 2'b00 : ((RMODE_B1_i == MODE_18) ? 2'b01 : ((RMODE_B1_i == MODE_9) ? 2'b10 : 2'b00)));
    fifo_ctl #(
        .ADDR_WIDTH(12),
        .FIFO_WIDTH(3'd4),
        .DEPTH(7)
    ) fifo36_ctl(
        .rclk(sclk_b1),
        .rst_R_n(flush1),
        .wclk(sclk_a1),
        .rst_W_n(flush1),
        .ren(REN_B1_i),
        .wen(ram_wen_a1),
        .sync(SYNC_FIFO1_i),
        .rmode(fifo_rmode),
        .wmode(fifo_wmode),
        .ren_o(ren_o),
        .fflags({FULL3, FMO3, FWM3, OVERRUN3, EMPTY3, EPO3, EWM3, UNDERRUN3}),
        .raddr(ff_raddr),
        .waddr(ff_waddr),
        .upaf(UPAF1_i),
        .upae(UPAE1_i)
    );
    TDP18K_FIFO #(
        .UPAF_i(UPAF1_i[10:0]),
        .UPAE_i(UPAE1_i[10:0]),
        .SYNC_FIFO_i(SYNC_FIFO1_i),
        .POWERDN_i(POWERDN1_i),
        .SLEEP_i(SLEEP1_i),
        .PROTECT_i(PROTECT1_i)
    )u1(
        .RMODE_A_i(ram_rmode_a1),
        .RMODE_B_i(ram_rmode_b1),
        .WMODE_A_i(ram_wmode_a1),
        .WMODE_B_i(ram_wmode_b1),
        .WEN_A_i(ram_wen_a1),
        .WEN_B_i(ram_wen_b1),
        .REN_A_i(ram_ren_a1),
        .REN_B_i(ram_ren_b1),
        .CLK_A_i(sclk_a1),
        .CLK_B_i(sclk_b1),
        .BE_A_i(ram_be_a1),
        .BE_B_i(ram_be_b1),
        .ADDR_A_i(ram_addr_a1),
        .ADDR_B_i(ram_addr_b1),
        .WDATA_A_i(ram_wdata_a1),
        .WDATA_B_i(ram_wdata_b1),
        .RDATA_A_o(ram_rdata_a1),
        .RDATA_B_o(ram_rdata_b1),
        .EMPTY_o(EMPTY1),
        .EPO_o(EPO1),
        .EWM_o(EWM1),
        .UNDERRUN_o(UNDERRUN1),
        .FULL_o(FULL1),
        .FMO_o(FMO1),
        .FWM_o(FWM1),
        .OVERRUN_o(OVERRUN1),
        .FLUSH_ni(flush1),
        .FMODE_i(ram_fmode1)
    );
    TDP18K_FIFO #(
        .UPAF_i(UPAF2_i),
        .UPAE_i(UPAE2_i),
        .SYNC_FIFO_i(SYNC_FIFO2_i),
        .POWERDN_i(POWERDN2_i),
        .SLEEP_i(SLEEP2_i),
        .PROTECT_i(PROTECT2_i)
    )u2(
        .RMODE_A_i(ram_rmode_a2),
        .RMODE_B_i(ram_rmode_b2),
        .WMODE_A_i(ram_wmode_a2),
        .WMODE_B_i(ram_wmode_b2),
        .WEN_A_i(ram_wen_a2),
        .WEN_B_i(ram_wen_b2),
        .REN_A_i(ram_ren_a2),
        .REN_B_i(ram_ren_b2),
        .CLK_A_i(sclk_a2),
        .CLK_B_i(sclk_b2),
        .BE_A_i(ram_be_a2),
        .BE_B_i(ram_be_b2),
        .ADDR_A_i(ram_addr_a2),
        .ADDR_B_i(ram_addr_b2),
        .WDATA_A_i(ram_wdata_a2),
        .WDATA_B_i(ram_wdata_b2),
        .RDATA_A_o(ram_rdata_a2),
        .RDATA_B_o(ram_rdata_b2),
        .EMPTY_o(EMPTY2),
        .EPO_o(EPO2),
        .EWM_o(EWM2),
        .UNDERRUN_o(UNDERRUN2),
        .FULL_o(FULL2),
        .FMO_o(FMO2),
        .FWM_o(FWM2),
        .OVERRUN_o(OVERRUN2),
        .FLUSH_ni(flush2),
        .FMODE_i(ram_fmode2)
    );
endmodule

module BRAM2x18_TDP (A1ADDR, A1DATA, A1EN, B1ADDR, B1DATA, B1EN, C1ADDR, C1DATA, C1EN, CLK1, CLK2, CLK3, CLK4, D1ADDR, D1DATA, D1EN, E1ADDR, E1DATA, E1EN, F1ADDR, F1DATA, F1EN, G1ADDR, G1DATA, G1EN, H1ADDR, H1DATA, H1EN);
    parameter CFG_ABITS = 11;
    parameter CFG_DBITS = 18;
    parameter CFG_ENABLE_B = 4;
    parameter CFG_ENABLE_D = 4;
    parameter CFG_ENABLE_F = 4;
    parameter CFG_ENABLE_H = 4;

    parameter CLKPOL2 = 1;
    parameter CLKPOL3 = 1;
    parameter [18431:0] INIT0 = 18432'bx;
    parameter [18431:0] INIT1 = 18432'bx;

    localparam MODE_36 = 3'b011; // 36- or 32-bit
    localparam MODE_18 = 3'b010; // 18- or 16-bit
    localparam MODE_9 = 3'b001; // 9- or 8-bit
    localparam MODE_4 = 3'b100; // 4-bit
    localparam MODE_2 = 3'b110; // 2-bit
    localparam MODE_1 = 3'b101; // 1-bit

    input CLK1;
    input CLK2;
    input CLK3;
    input CLK4;

    input [CFG_ABITS-1:0] A1ADDR;
    output [CFG_DBITS-1:0] A1DATA;
    input A1EN;

    input [CFG_ABITS-1:0] B1ADDR;
    input [CFG_DBITS-1:0] B1DATA;
    input [CFG_ENABLE_B-1:0] B1EN;

    input [CFG_ABITS-1:0] C1ADDR;
    output [CFG_DBITS-1:0] C1DATA;
    input C1EN;

    input [CFG_ABITS-1:0] D1ADDR;
    input [CFG_DBITS-1:0] D1DATA;
    input [CFG_ENABLE_D-1:0] D1EN;

    input [CFG_ABITS-1:0] E1ADDR;
    output [CFG_DBITS-1:0] E1DATA;
    input E1EN;

    input [CFG_ABITS-1:0] F1ADDR;
    input [CFG_DBITS-1:0] F1DATA;
    input [CFG_ENABLE_F-1:0] F1EN;

    input [CFG_ABITS-1:0] G1ADDR;
    output [CFG_DBITS-1:0] G1DATA;
    input G1EN;

    input [CFG_ABITS-1:0] H1ADDR;
    input [CFG_DBITS-1:0] H1DATA;
    input [CFG_ENABLE_H-1:0] H1EN;

    wire FLUSH1;
    wire FLUSH2;
    wire SPLIT;

    wire [13:CFG_ABITS] A1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] B1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] C1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] D1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] E1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] F1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] G1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
    wire [13:CFG_ABITS] H1ADDR_CMPL = {14-CFG_ABITS{1'b0}};

    wire [13:0] A1ADDR_TOTAL = {A1ADDR_CMPL, A1ADDR};
    wire [13:0] B1ADDR_TOTAL = {B1ADDR_CMPL, B1ADDR};
    wire [13:0] C1ADDR_TOTAL = {C1ADDR_CMPL, C1ADDR};
    wire [13:0] D1ADDR_TOTAL = {D1ADDR_CMPL, D1ADDR};
    wire [13:0] E1ADDR_TOTAL = {E1ADDR_CMPL, E1ADDR};
    wire [13:0] F1ADDR_TOTAL = {F1ADDR_CMPL, F1ADDR};
    wire [13:0] G1ADDR_TOTAL = {G1ADDR_CMPL, G1ADDR};
    wire [13:0] H1ADDR_TOTAL = {H1ADDR_CMPL, H1ADDR};

    wire [17:CFG_DBITS] A1_RDATA_CMPL;
    wire [17:CFG_DBITS] C1_RDATA_CMPL;
    wire [17:CFG_DBITS] E1_RDATA_CMPL;
    wire [17:CFG_DBITS] G1_RDATA_CMPL;

    wire [17:CFG_DBITS] B1_WDATA_CMPL;
    wire [17:CFG_DBITS] D1_WDATA_CMPL;
    wire [17:CFG_DBITS] F1_WDATA_CMPL;
    wire [17:CFG_DBITS] H1_WDATA_CMPL;

    wire [13:0] PORT_A1_ADDR;
    wire [13:0] PORT_A2_ADDR;
    wire [13:0] PORT_B1_ADDR;
    wire [13:0] PORT_B2_ADDR;

    case (CFG_DBITS)
        1: begin
            assign PORT_A1_ADDR = A1EN ? A1ADDR_TOTAL : (B1EN ? B1ADDR_TOTAL : 14'd0);
            assign PORT_B1_ADDR = C1EN ? C1ADDR_TOTAL : (D1EN ? D1ADDR_TOTAL : 14'd0);
            assign PORT_A2_ADDR = E1EN ? E1ADDR_TOTAL : (F1EN ? F1ADDR_TOTAL : 14'd0);
            assign PORT_B2_ADDR = G1EN ? G1ADDR_TOTAL : (H1EN ? H1ADDR_TOTAL : 14'd0);
	    defparam bram_2x18k.MODE_BITS = { 1'b1,
		11'd10, 11'd10, 4'd0, MODE_1, MODE_1, MODE_1, MODE_1, 1'd0,
		12'd10, 12'd10, 4'd0, MODE_1, MODE_1, MODE_1, MODE_1, 1'd0
	    };
        end

        2: begin
            assign PORT_A1_ADDR = A1EN ? (A1ADDR_TOTAL << 1) : (B1EN ? (B1ADDR_TOTAL << 1) : 14'd0);
            assign PORT_B1_ADDR = C1EN ? (C1ADDR_TOTAL << 1) : (D1EN ? (D1ADDR_TOTAL << 1) : 14'd0);
            assign PORT_A2_ADDR = E1EN ? (E1ADDR_TOTAL << 1) : (F1EN ? (F1ADDR_TOTAL << 1) : 14'd0);
            assign PORT_B2_ADDR = G1EN ? (G1ADDR_TOTAL << 1) : (H1EN ? (H1ADDR_TOTAL << 1) : 14'd0);
	    defparam bram_2x18k.MODE_BITS = { 1'b1,
		11'd10, 11'd10, 4'd0, MODE_2, MODE_2, MODE_2, MODE_2, 1'd0,
		12'd10, 12'd10, 4'd0, MODE_2, MODE_2, MODE_2, MODE_2, 1'd0
	    };
        end

        4: begin
            assign PORT_A1_ADDR = A1EN ? (A1ADDR_TOTAL << 2) : (B1EN ? (B1ADDR_TOTAL << 2) : 14'd0);
            assign PORT_B1_ADDR = C1EN ? (C1ADDR_TOTAL << 2) : (D1EN ? (D1ADDR_TOTAL << 2) : 14'd0);
            assign PORT_A2_ADDR = E1EN ? (E1ADDR_TOTAL << 2) : (F1EN ? (F1ADDR_TOTAL << 2) : 14'd0);
            assign PORT_B2_ADDR = G1EN ? (G1ADDR_TOTAL << 2) : (H1EN ? (H1ADDR_TOTAL << 2) : 14'd0);
	    defparam bram_2x18k.MODE_BITS = { 1'b1,
		11'd10, 11'd10, 4'd0, MODE_4, MODE_4, MODE_4, MODE_4, 1'd0,
		12'd10, 12'd10, 4'd0, MODE_4, MODE_4, MODE_4, MODE_4, 1'd0
	    };
        end

        8, 9: begin
            assign PORT_A1_ADDR = A1EN ? (A1ADDR_TOTAL << 3) : (B1EN ? (B1ADDR_TOTAL << 3) : 14'd0);
            assign PORT_B1_ADDR = C1EN ? (C1ADDR_TOTAL << 3) : (D1EN ? (D1ADDR_TOTAL << 3) : 14'd0);
            assign PORT_A2_ADDR = E1EN ? (E1ADDR_TOTAL << 3) : (F1EN ? (F1ADDR_TOTAL << 3) : 14'd0);
            assign PORT_B2_ADDR = G1EN ? (G1ADDR_TOTAL << 3) : (H1EN ? (H1ADDR_TOTAL << 3) : 14'd0);
	    defparam bram_2x18k.MODE_BITS = { 1'b1,
		11'd10, 11'd10, 4'd0, MODE_9, MODE_9, MODE_9, MODE_9, 1'd0,
		12'd10, 12'd10, 4'd0, MODE_9, MODE_9, MODE_9, MODE_9, 1'd0
	    };
        end

        16, 18: begin
            assign PORT_A1_ADDR = A1EN ? (A1ADDR_TOTAL << 4) : (B1EN ? (B1ADDR_TOTAL << 4) : 14'd0);
            assign PORT_B1_ADDR = C1EN ? (C1ADDR_TOTAL << 4) : (D1EN ? (D1ADDR_TOTAL << 4) : 14'd0);
            assign PORT_A2_ADDR = E1EN ? (E1ADDR_TOTAL << 4) : (F1EN ? (F1ADDR_TOTAL << 4) : 14'd0);
            assign PORT_B2_ADDR = G1EN ? (G1ADDR_TOTAL << 4) : (H1EN ? (H1ADDR_TOTAL << 4) : 14'd0);
	    defparam bram_2x18k.MODE_BITS = { 1'b1,
		11'd10, 11'd10, 4'd0, MODE_18, MODE_18, MODE_18, MODE_18, 1'd0,
		12'd10, 12'd10, 4'd0, MODE_18, MODE_18, MODE_18, MODE_18, 1'd0
	    };
        end

        default: begin
            assign PORT_A1_ADDR = A1EN ? A1ADDR_TOTAL : (B1EN ? B1ADDR_TOTAL : 14'd0);
            assign PORT_B1_ADDR = C1EN ? C1ADDR_TOTAL : (D1EN ? D1ADDR_TOTAL : 14'd0);
            assign PORT_A2_ADDR = E1EN ? E1ADDR_TOTAL : (F1EN ? F1ADDR_TOTAL : 14'd0);
            assign PORT_B2_ADDR = G1EN ? G1ADDR_TOTAL : (H1EN ? H1ADDR_TOTAL : 14'd0);
	    defparam bram_2x18k.MODE_BITS = { 1'b1,
	        11'd10, 11'd10, 4'd0, MODE_36, MODE_36, MODE_36, MODE_36, 1'd0,
	        12'd10, 12'd10, 4'd0, MODE_36, MODE_36, MODE_36, MODE_36, 1'd0
	    };
        end
    endcase

    assign FLUSH1 = 1'b0;
    assign FLUSH2 = 1'b0;

    wire [17:0] PORT_A1_RDATA = {A1_RDATA_CMPL, A1DATA};
    wire [17:0] PORT_B1_RDATA = {C1_RDATA_CMPL, C1DATA};
    wire [17:0] PORT_A2_RDATA = {E1_RDATA_CMPL, E1DATA};
    wire [17:0] PORT_B2_RDATA = {G1_RDATA_CMPL, G1DATA};

    wire [17:0] PORT_A1_WDATA = {B1_WDATA_CMPL, B1DATA};
    wire [17:0] PORT_B1_WDATA = {D1_WDATA_CMPL, D1DATA};
    wire [17:0] PORT_A2_WDATA = {F1_WDATA_CMPL, F1DATA};
    wire [17:0] PORT_B2_WDATA = {H1_WDATA_CMPL, H1DATA};

    wire PORT_A1_CLK = CLK1;
    wire PORT_A2_CLK = CLK3;
    wire PORT_B1_CLK = CLK2;
    wire PORT_B2_CLK = CLK4;

    wire PORT_A1_REN = A1EN;
    wire PORT_A1_WEN = B1EN[0];
    wire [CFG_ENABLE_B-1:0] PORT_A1_BE = {B1EN[1],B1EN[0]};

    wire PORT_A2_REN = E1EN;
    wire PORT_A2_WEN = F1EN[0];
    wire [CFG_ENABLE_F-1:0] PORT_A2_BE = {F1EN[1],F1EN[0]};

    wire PORT_B1_REN = C1EN;
    wire PORT_B1_WEN = D1EN[0];
    wire [CFG_ENABLE_D-1:0] PORT_B1_BE = {D1EN[1],D1EN[0]};

    wire PORT_B2_REN = G1EN;
    wire PORT_B2_WEN = H1EN[0];
    wire [CFG_ENABLE_H-1:0] PORT_B2_BE = {H1EN[1],H1EN[0]};

    TDP36K bram_2x18k (
        .WDATA_A1_i(PORT_A1_WDATA),
        .RDATA_A1_o(PORT_A1_RDATA),
        .ADDR_A1_i(PORT_A1_ADDR),
        .CLK_A1_i(PORT_A1_CLK),
        .REN_A1_i(PORT_A1_REN),
        .WEN_A1_i(PORT_A1_WEN),
        .BE_A1_i(PORT_A1_BE),

        .WDATA_A2_i(PORT_A2_WDATA),
        .RDATA_A2_o(PORT_A2_RDATA),
        .ADDR_A2_i(PORT_A2_ADDR),
        .CLK_A2_i(PORT_A2_CLK),
        .REN_A2_i(PORT_A2_REN),
        .WEN_A2_i(PORT_A2_WEN),
        .BE_A2_i(PORT_A2_BE),

        .WDATA_B1_i(PORT_B1_WDATA),
        .RDATA_B1_o(PORT_B1_RDATA),
        .ADDR_B1_i(PORT_B1_ADDR),
        .CLK_B1_i(PORT_B1_CLK),
        .REN_B1_i(PORT_B1_REN),
        .WEN_B1_i(PORT_B1_WEN),
        .BE_B1_i(PORT_B1_BE),

        .WDATA_B2_i(PORT_B2_WDATA),
        .RDATA_B2_o(PORT_B2_RDATA),
        .ADDR_B2_i(PORT_B2_ADDR),
        .CLK_B2_i(PORT_B2_CLK),
        .REN_B2_i(PORT_B2_REN),
        .WEN_B2_i(PORT_B2_WEN),
        .BE_B2_i(PORT_B2_BE),

        .FLUSH1_i(FLUSH1),
        .FLUSH2_i(FLUSH2)
    );
endmodule

module BRAM2x18_SDP (A1ADDR, A1DATA, A1EN, B1ADDR, B1DATA, B1EN, C1ADDR, C1DATA, C1EN, CLK1, CLK2, D1ADDR, D1DATA, D1EN);
	parameter CFG_ABITS = 11;
	parameter CFG_DBITS = 18;
	parameter CFG_ENABLE_B = 4;
	parameter CFG_ENABLE_D = 4;

	parameter CLKPOL2 = 1;
	parameter CLKPOL3 = 1;
	parameter [18431:0] INIT0 = 18432'bx;
	parameter [18431:0] INIT1 = 18432'bx;

        localparam MODE_36 = 3'b011; // 36- or 32-bit
        localparam MODE_18 = 3'b010; // 18- or 16-bit
        localparam MODE_9 = 3'b001; // 9- or 8-bit
        localparam MODE_4 = 3'b100; // 4-bit
        localparam MODE_2 = 3'b110; // 2-bit
        localparam MODE_1 = 3'b101; // 1-bit

	input CLK1;
	input CLK2;

	input [CFG_ABITS-1:0] A1ADDR;
	output [CFG_DBITS-1:0] A1DATA;
	input A1EN;

	input [CFG_ABITS-1:0] B1ADDR;
	input [CFG_DBITS-1:0] B1DATA;
	input [CFG_ENABLE_B-1:0] B1EN;

	input [CFG_ABITS-1:0] C1ADDR;
	output [CFG_DBITS-1:0] C1DATA;
	input C1EN;

	input [CFG_ABITS-1:0] D1ADDR;
	input [CFG_DBITS-1:0] D1DATA;
	input [CFG_ENABLE_D-1:0] D1EN;

	wire FLUSH1;
	wire FLUSH2;

	wire [13:CFG_ABITS] A1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
	wire [13:CFG_ABITS] B1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
	wire [13:CFG_ABITS] C1ADDR_CMPL = {14-CFG_ABITS{1'b0}};
	wire [13:CFG_ABITS] D1ADDR_CMPL = {14-CFG_ABITS{1'b0}};

	wire [13:0] A1ADDR_TOTAL = {A1ADDR_CMPL, A1ADDR};
	wire [13:0] B1ADDR_TOTAL = {B1ADDR_CMPL, B1ADDR};
	wire [13:0] C1ADDR_TOTAL = {C1ADDR_CMPL, C1ADDR};
	wire [13:0] D1ADDR_TOTAL = {D1ADDR_CMPL, D1ADDR};

	wire [17:CFG_DBITS] A1_RDATA_CMPL;
	wire [17:CFG_DBITS] C1_RDATA_CMPL;

	wire [17:CFG_DBITS] B1_WDATA_CMPL;
	wire [17:CFG_DBITS] D1_WDATA_CMPL;

	wire [13:0] PORT_A1_ADDR;
	wire [13:0] PORT_A2_ADDR;
	wire [13:0] PORT_B1_ADDR;
	wire [13:0] PORT_B2_ADDR;

	case (CFG_DBITS)
		1: begin
			assign PORT_A1_ADDR = A1ADDR_TOTAL;
			assign PORT_B1_ADDR = B1ADDR_TOTAL;
			assign PORT_A2_ADDR = C1ADDR_TOTAL;
			assign PORT_B2_ADDR = D1ADDR_TOTAL;
			defparam bram_2x18k.MODE_BITS = { 1'b1,
				11'd10, 11'd10, 4'd0, MODE_1, MODE_1, MODE_1, MODE_1, 1'd0,
				12'd10, 12'd10, 4'd0, MODE_1, MODE_1, MODE_1, MODE_1, 1'd0
			};
		end

		2: begin
			assign PORT_A1_ADDR = A1ADDR_TOTAL << 1;
			assign PORT_B1_ADDR = B1ADDR_TOTAL << 1;
			assign PORT_A2_ADDR = C1ADDR_TOTAL << 1;
			assign PORT_B2_ADDR = D1ADDR_TOTAL << 1;
			defparam bram_2x18k.MODE_BITS = { 1'b1,
				11'd10, 11'd10, 4'd0, MODE_2, MODE_2, MODE_2, MODE_2, 1'd0,
				12'd10, 12'd10, 4'd0, MODE_2, MODE_2, MODE_2, MODE_2, 1'd0
			};
		end

		4: begin
			assign PORT_A1_ADDR = A1ADDR_TOTAL << 2;
			assign PORT_B1_ADDR = B1ADDR_TOTAL << 2;
			assign PORT_A2_ADDR = C1ADDR_TOTAL << 2;
			assign PORT_B2_ADDR = D1ADDR_TOTAL << 2;
			defparam bram_2x18k.MODE_BITS = { 1'b1,
				11'd10, 11'd10, 4'd0, MODE_4, MODE_4, MODE_4, MODE_4, 1'd0,
				12'd10, 12'd10, 4'd0, MODE_4, MODE_4, MODE_4, MODE_4, 1'd0
			};
		end

		8, 9: begin
			assign PORT_A1_ADDR = A1ADDR_TOTAL << 3;
			assign PORT_B1_ADDR = B1ADDR_TOTAL << 3;
			assign PORT_A2_ADDR = C1ADDR_TOTAL << 3;
			assign PORT_B2_ADDR = D1ADDR_TOTAL << 3;
			defparam bram_2x18k.MODE_BITS = { 1'b1,
				11'd10, 11'd10, 4'd0, MODE_9, MODE_9, MODE_9, MODE_9, 1'd0,
				12'd10, 12'd10, 4'd0, MODE_9, MODE_9, MODE_9, MODE_9, 1'd0
			};
		end

		16, 18: begin
			assign PORT_A1_ADDR = A1ADDR_TOTAL << 4;
			assign PORT_B1_ADDR = B1ADDR_TOTAL << 4;
			assign PORT_A2_ADDR = C1ADDR_TOTAL << 4;
			assign PORT_B2_ADDR = D1ADDR_TOTAL << 4;
			defparam bram_2x18k.MODE_BITS = { 1'b1,
				11'd10, 11'd10, 4'd0, MODE_18, MODE_18, MODE_18, MODE_18, 1'd0,
				12'd10, 12'd10, 4'd0, MODE_18, MODE_18, MODE_18, MODE_18, 1'd0
			};
		end

		default: begin
			assign PORT_A1_ADDR = A1ADDR_TOTAL;
			assign PORT_B1_ADDR = B1ADDR_TOTAL;
			assign PORT_A2_ADDR = D1ADDR_TOTAL;
			assign PORT_B2_ADDR = C1ADDR_TOTAL;
			defparam bram_2x18k.MODE_BITS = { 1'b1,
				11'd10, 11'd10, 4'd0, MODE_36, MODE_36, MODE_36, MODE_36, 1'd0,
				12'd10, 12'd10, 4'd0, MODE_36, MODE_36, MODE_36, MODE_36, 1'd0
			};
		end
	endcase

	assign FLUSH1 = 1'b0;
	assign FLUSH2 = 1'b0;

	wire [17:0] PORT_A1_RDATA;
	wire [17:0] PORT_B1_RDATA;
	wire [17:0] PORT_A2_RDATA;
	wire [17:0] PORT_B2_RDATA;

	wire [17:0] PORT_A1_WDATA;
	wire [17:0] PORT_B1_WDATA;
	wire [17:0] PORT_A2_WDATA;
	wire [17:0] PORT_B2_WDATA;

	// Assign read/write data - handle special case for 9bit mode
	// parity bit for 9bit mode is placed in R/W port on bit #16
	case (CFG_DBITS)
		9: begin
			assign A1DATA = {PORT_A1_RDATA[16], PORT_A1_RDATA[7:0]};
			assign C1DATA = {PORT_A2_RDATA[16], PORT_A2_RDATA[7:0]};
			assign PORT_A1_WDATA = {18{1'b0}};
			assign PORT_B1_WDATA = {B1_WDATA_CMPL[17], B1DATA[8], B1_WDATA_CMPL[16:9], B1DATA[7:0]};
			assign PORT_A2_WDATA = {18{1'b0}};
			assign PORT_B2_WDATA = {D1_WDATA_CMPL[17], D1DATA[8], D1_WDATA_CMPL[16:9], D1DATA[7:0]};
		end
		default: begin
			assign A1DATA = PORT_A1_RDATA[CFG_DBITS-1:0];
			assign C1DATA = PORT_A2_RDATA[CFG_DBITS-1:0];
			assign PORT_A1_WDATA = {18{1'b1}};
			assign PORT_B1_WDATA = {B1_WDATA_CMPL, B1DATA};
			assign PORT_A2_WDATA = {18{1'b1}};
			assign PORT_B2_WDATA = {D1_WDATA_CMPL, D1DATA};

		end
	endcase

	wire PORT_A1_CLK = CLK1;
	wire PORT_A2_CLK = CLK2;
	wire PORT_B1_CLK = CLK1;
	wire PORT_B2_CLK = CLK2;

	wire PORT_A1_REN = A1EN;
	wire PORT_A1_WEN = 1'b0;
	wire [CFG_ENABLE_B-1:0] PORT_A1_BE = {PORT_A1_WEN,PORT_A1_WEN};

	wire PORT_A2_REN = C1EN;
	wire PORT_A2_WEN = 1'b0;
	wire [CFG_ENABLE_D-1:0] PORT_A2_BE = {PORT_A2_WEN,PORT_A2_WEN};

	wire PORT_B1_REN = 1'b0;
	wire PORT_B1_WEN = B1EN[0];
	wire [CFG_ENABLE_B-1:0] PORT_B1_BE = {B1EN[1],B1EN[0]};

	wire PORT_B2_REN = 1'b0;
	wire PORT_B2_WEN = D1EN[0];
	wire [CFG_ENABLE_D-1:0] PORT_B2_BE = {D1EN[1],D1EN[0]};

	TDP36K  bram_2x18k (
		.WDATA_A1_i(PORT_A1_WDATA),
		.RDATA_A1_o(PORT_A1_RDATA),
		.ADDR_A1_i(PORT_A1_ADDR),
		.CLK_A1_i(PORT_A1_CLK),
		.REN_A1_i(PORT_A1_REN),
		.WEN_A1_i(PORT_A1_WEN),
		.BE_A1_i(PORT_A1_BE),

		.WDATA_A2_i(PORT_A2_WDATA),
		.RDATA_A2_o(PORT_A2_RDATA),
		.ADDR_A2_i(PORT_A2_ADDR),
		.CLK_A2_i(PORT_A2_CLK),
		.REN_A2_i(PORT_A2_REN),
		.WEN_A2_i(PORT_A2_WEN),
		.BE_A2_i(PORT_A2_BE),

		.WDATA_B1_i(PORT_B1_WDATA),
		.RDATA_B1_o(PORT_B1_RDATA),
		.ADDR_B1_i(PORT_B1_ADDR),
		.CLK_B1_i(PORT_B1_CLK),
		.REN_B1_i(PORT_B1_REN),
		.WEN_B1_i(PORT_B1_WEN),
		.BE_B1_i(PORT_B1_BE),

		.WDATA_B2_i(PORT_B2_WDATA),
		.RDATA_B2_o(PORT_B2_RDATA),
		.ADDR_B2_i(PORT_B2_ADDR),
		.CLK_B2_i(PORT_B2_CLK),
		.REN_B2_i(PORT_B2_REN),
		.WEN_B2_i(PORT_B2_WEN),
		.BE_B2_i(PORT_B2_BE),

		.FLUSH1_i(FLUSH1),
		.FLUSH2_i(FLUSH2)
	);
endmodule

(* blackbox *)
module QL_DSP1 (
    input wire [19:0] a,
    input wire [17:0] b,
    (* clkbuf_sink *)
    input wire clk0,
    (* clkbuf_sink *)
    input wire clk1,
    input wire [ 1:0] feedback0,
    input wire [ 1:0] feedback1,
    input wire        load_acc0,
    input wire        load_acc1,
    input wire        reset0,
    input wire        reset1,
    output reg [37:0] z
);
    parameter MODE_BITS = 27'b00000000000000000000000000;
endmodule  /* QL_DSP1 */

module QL_DSP2 ( // TODO: Name subject to change
    input  wire [19:0] a,
    input  wire [17:0] b,
    input  wire [ 5:0] acc_fir,
    output wire [37:0] z,
    output wire [17:0] dly_b,

    (* clkbuf_sink *)
    input  wire       clk,
    input  wire       reset,

    input  wire [2:0] feedback,
    input  wire       load_acc,
    input  wire       unsigned_a,
    input  wire       unsigned_b,

    input  wire       f_mode,
    input  wire [2:0] output_select,
    input  wire       saturate_enable,
    input  wire [5:0] shift_right,
    input  wire       round,
    input  wire       subtract,
    input  wire       register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

      localparam NBITS_ACC = 64;
      localparam NBITS_A = 20;
      localparam NBITS_B = 18;
      localparam NBITS_Z = 38;

      wire [NBITS_Z-1:0] dsp_full_z;
      wire [(NBITS_Z/2)-1:0] dsp_frac0_z;
      wire [(NBITS_Z/2)-1:0] dsp_frac1_z;

      wire [NBITS_B-1:0] dsp_full_dly_b;
      wire [(NBITS_B/2)-1:0] dsp_frac0_dly_b;
      wire [(NBITS_B/2)-1:0] dsp_frac1_dly_b;

      assign z = f_mode ? {dsp_frac1_z, dsp_frac0_z} : dsp_full_z;
      assign dly_b = f_mode ? {dsp_frac1_dly_b, dsp_frac0_dly_b} : dsp_full_dly_b;

    // Output used when fmode == 1
        dsp_t1_sim #(
        .NBITS_A(NBITS_A/2),
            .NBITS_B(NBITS_B/2),
            .NBITS_ACC(NBITS_ACC/2),
            .NBITS_Z(NBITS_Z/2)
        ) dsp_frac0 (
            .a_i(a[(NBITS_A/2)-1:0]),
            .b_i(b[(NBITS_B/2)-1:0]),
            .z_o(dsp_frac0_z),
            .dly_b_o(dsp_frac0_dly_b),

            .acc_fir_i(acc_fir),
            .feedback_i(feedback),
            .load_acc_i(load_acc),

            .unsigned_a_i(unsigned_a),
            .unsigned_b_i(unsigned_b),

            .clock_i(clk),
            .s_reset(reset),

            .saturate_enable_i(saturate_enable),
            .output_select_i(output_select),
            .round_i(round),
            .shift_right_i(shift_right),
            .subtract_i(subtract),
            .register_inputs_i(register_inputs),
            .coef_0_i(COEFF_0[(NBITS_A/2)-1:0]),
            .coef_1_i(COEFF_1[(NBITS_A/2)-1:0]),
            .coef_2_i(COEFF_2[(NBITS_A/2)-1:0]),
            .coef_3_i(COEFF_3[(NBITS_A/2)-1:0])
        );

    // Output used when fmode == 1
        dsp_t1_sim #(
        .NBITS_A(NBITS_A/2),
            .NBITS_B(NBITS_B/2),
            .NBITS_ACC(NBITS_ACC/2),
            .NBITS_Z(NBITS_Z/2)
        ) dsp_frac1 (
            .a_i(a[NBITS_A-1:NBITS_A/2]),
            .b_i(b[NBITS_B-1:NBITS_B/2]),
            .z_o(dsp_frac1_z),
            .dly_b_o(dsp_frac1_dly_b),

            .acc_fir_i(acc_fir),
            .feedback_i(feedback),
            .load_acc_i(load_acc),

            .unsigned_a_i(unsigned_a),
            .unsigned_b_i(unsigned_b),

            .clock_i(clk),
            .s_reset(reset),

            .saturate_enable_i(saturate_enable),
            .output_select_i(output_select),
            .round_i(round),
            .shift_right_i(shift_right),
            .subtract_i(subtract),
            .register_inputs_i(register_inputs),
            .coef_0_i(COEFF_0[NBITS_A-1:NBITS_A/2]),
            .coef_1_i(COEFF_1[NBITS_A-1:NBITS_A/2]),
            .coef_2_i(COEFF_2[NBITS_A-1:NBITS_A/2]),
            .coef_3_i(COEFF_3[NBITS_A-1:NBITS_A/2])
        );

    // Output used when fmode == 0
        dsp_t1_sim #(
             .NBITS_A(NBITS_A),
             .NBITS_B(NBITS_B),
             .NBITS_ACC(NBITS_ACC),
             .NBITS_Z(NBITS_Z)
        ) dsp_full (
            .a_i(a),
            .b_i(b),
            .z_o(dsp_full_z),
            .dly_b_o(dsp_full_dly_b),

            .acc_fir_i(acc_fir),
            .feedback_i(feedback),
            .load_acc_i(load_acc),

            .unsigned_a_i(unsigned_a),
            .unsigned_b_i(unsigned_b),

            .clock_i(clk),
            .s_reset(reset),

            .saturate_enable_i(saturate_enable),
            .output_select_i(output_select),
            .round_i(round),
            .shift_right_i(shift_right),
            .subtract_i(subtract),
            .register_inputs_i(register_inputs),
            .coef_0_i(COEFF_0),
            .coef_1_i(COEFF_1),
            .coef_2_i(COEFF_2),
            .coef_3_i(COEFF_3)
        );
endmodule

module QL_DSP2_MULT ( // TODO: Name subject to change
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    // Port not available in architecture file
    input  wire       reset,

    input  wire       unsigned_a,
    input  wire       unsigned_b,

    input  wire       f_mode,
    input  wire [2:0] output_select,
    input  wire       register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

	.reset(reset),

        .f_mode(f_mode),

        .feedback(3'b0),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .output_select(3'b0),	// unregistered output: a * b (0)
        .register_inputs(1'b0)  // unregistered inputs
    );
endmodule

module QL_DSP2_MULT_REGIN ( // TODO: Name subject to change
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire       clk,
    // Port not available in architecture file
    input  wire       reset,

    input  wire       unsigned_a,
    input  wire       unsigned_b,

    input  wire       f_mode,
    input  wire [2:0] output_select,
    input  wire       register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(3'b0),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(3'b0),	// unregistered output: a * b (0)
        .register_inputs(1'b1)  // registered inputs
    );
endmodule

module QL_DSP2_MULT_REGOUT ( // TODO: Name subject to change
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire       clk,
    // Port not available in architecture file
    input  wire       reset,

    input  wire       unsigned_a,
    input  wire       unsigned_b,
    input  wire       f_mode,
    input  wire [2:0] output_select,
    input  wire       register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(3'b0),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(3'b100),	// registered output: a * b (4)
        .register_inputs(1'b0)  // unregistered inputs
    );
endmodule

module QL_DSP2_MULT_REGIN_REGOUT ( // TODO: Name subject to change
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire       clk,
    // Port not available in architecture file
    input  wire       reset,

    input  wire       unsigned_a,
    input  wire       unsigned_b,
    input  wire       f_mode,
    input  wire [2:0] output_select,
    input  wire       register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(3'b0),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(3'b100),	// registered output: a * b (4)
        .register_inputs(1'b1)  // registered inputs
    );
endmodule

module QL_DSP2_MULTADD (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    // begin: Ports not available in architecture file
    (* clkbuf_sink *)
    input  wire        clk,
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    // end: Ports not available in architecture file
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
        .load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(output_select),	// unregistered output: ACCin (2, 3)
        .subtract(subtract),
        .register_inputs(1'b0)  // unregistered inputs
    );
endmodule

module QL_DSP2_MULTADD_REGIN (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // Port not available in architecture file
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
        .load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(output_select),	// unregistered output: ACCin (2, 3)
        .subtract(subtract),
        .register_inputs(1'b1)  // registered inputs
    );
endmodule

module QL_DSP2_MULTADD_REGOUT (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // Port not available in architecture file
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
        .load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(output_select),	// registered output: ACCin (6, 7)
        .subtract(subtract),
        .register_inputs(1'b0)  // unregistered inputs
    );
endmodule

module QL_DSP2_MULTADD_REGIN_REGOUT (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // Port not available in architecture file
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
        .load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(output_select),	// registered output: ACCin (6, 7)
        .subtract(subtract),
        .register_inputs(1'b1)  // registered inputs
    );
endmodule

module QL_DSP2_MULTACC (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // begin: Ports not available in architecture file
    input  wire        reset,

    input  wire        load_acc,
    // end: Ports not available in architecture file
    input  wire [ 2:0] feedback,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

	.feedback(feedback),
	.load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
        .reset(reset),

        .output_select(1'b1),	// unregistered output: ACCout (1)
        .subtract(subtract),
        .register_inputs(1'b0)  // unregistered inputs
    );
endmodule

module QL_DSP2_MULTACC_REGIN (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // Port not available in architecture file
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
        .load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(1'b1),	// unregistered output: ACCout (1)
        .subtract(subtract),
        .register_inputs(1'b1)  // registered inputs
    );
endmodule

module QL_DSP2_MULTACC_REGOUT (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // Port not available in architecture file
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
	.load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(3'b101),	// registered output: ACCout (5)
        .subtract(subtract),
        .register_inputs(1'b0)  // unregistered inputs
    );
endmodule

module QL_DSP2_MULTACC_REGIN_REGOUT (
    input  wire [19:0] a,
    input  wire [17:0] b,
    output wire [37:0] z,

    (* clkbuf_sink *)
    input  wire        clk,
    // Port not available in architecture file
    input  wire        reset,

    input  wire [ 2:0] feedback,
    input  wire        load_acc,
    input  wire        unsigned_a,
    input  wire        unsigned_b,

    input  wire        f_mode,
    input  wire [ 2:0] output_select,
    input  wire        subtract,
    input  wire        register_inputs
);

    parameter [79:0] MODE_BITS = 80'd0;

    localparam [19:0] COEFF_0 = MODE_BITS[19:0];
    localparam [19:0] COEFF_1 = MODE_BITS[39:20];
    localparam [19:0] COEFF_2 = MODE_BITS[59:40];
    localparam [19:0] COEFF_3 = MODE_BITS[79:60];

    QL_DSP2 #(
        .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
    ) dsp (
        .a(a),
        .b(b),
        .z(z),

        .f_mode(f_mode),

        .feedback(feedback),
        .load_acc(load_acc),

        .unsigned_a(unsigned_a),
        .unsigned_b(unsigned_b),

        .clk(clk),
	.reset(reset),

        .output_select(3'b101),	// registered output: ACCout (5)
        .subtract(subtract),
        .register_inputs(1'b1)  // registered inputs
    );
endmodule

module dsp_t1_sim # (
    parameter NBITS_ACC  = 64,
    parameter NBITS_A    = 20,
    parameter NBITS_B    = 18,
    parameter NBITS_Z    = 38
)(
    input  wire [NBITS_A-1:0] a_i,
    input  wire [NBITS_B-1:0] b_i,
    output wire [NBITS_Z-1:0] z_o,
    output reg  [NBITS_B-1:0] dly_b_o,

    input  wire [5:0]         acc_fir_i,
    input  wire [2:0]         feedback_i,
    input  wire               load_acc_i,

    input  wire               unsigned_a_i,
    input  wire               unsigned_b_i,

    input  wire               clock_i,
    input  wire               s_reset,

    input  wire               saturate_enable_i,
    input  wire [2:0]         output_select_i,
    input  wire               round_i,
    input  wire [5:0]         shift_right_i,
    input  wire               subtract_i,
    input  wire               register_inputs_i,
    input  wire [NBITS_A-1:0] coef_0_i,
    input  wire [NBITS_A-1:0] coef_1_i,
    input  wire [NBITS_A-1:0] coef_2_i,
    input  wire [NBITS_A-1:0] coef_3_i
);

// FIXME: The version of Icarus Verilog from Conda seems not to recognize the
// $error macro. Disable this sanity check for now because of that.
`ifndef __ICARUS__
    if (NBITS_ACC < NBITS_A + NBITS_B)
        $error("NBITS_ACC must be > NBITS_A + NBITS_B");
`endif

    // Input registers
    reg  [NBITS_A-1:0]  r_a;
    reg  [NBITS_B-1:0]  r_b;
    reg  [5:0]          r_acc_fir;
    reg                 r_unsigned_a;
    reg                 r_unsigned_b;
    reg                 r_load_acc;
    reg  [2:0]          r_feedback;
    reg  [5:0]          r_shift_d1;
    reg  [5:0]          r_shift_d2;
    reg         r_subtract;
    reg         r_sat;
    reg         r_rnd;
    reg [NBITS_ACC-1:0] acc;

    initial begin
        r_a          <= 0;
        r_b          <= 0;

        r_acc_fir    <= 0;
        r_unsigned_a <= 0;
        r_unsigned_b <= 0;
        r_feedback   <= 0;
        r_shift_d1   <= 0;
        r_shift_d2   <= 0;
        r_subtract   <= 0;
        r_load_acc   <= 0;
        r_sat        <= 0;
        r_rnd        <= 0;
    end

    always @(posedge clock_i or posedge s_reset) begin
        if (s_reset) begin

            r_a <= 'h0;
            r_b <= 'h0;

        r_acc_fir    <= 0;
            r_unsigned_a <= 0;
            r_unsigned_b <= 0;
            r_feedback   <= 0;
            r_shift_d1   <= 0;
            r_shift_d2   <= 0;
        r_subtract   <= 0;
            r_load_acc   <= 0;
            r_sat    <= 0;
            r_rnd    <= 0;

        end else begin

            r_a <= a_i;
            r_b <= b_i;

        r_acc_fir    <= acc_fir_i;
            r_unsigned_a <= unsigned_a_i;
            r_unsigned_b <= unsigned_b_i;
            r_feedback   <= feedback_i;
            r_shift_d1   <= shift_right_i;
            r_shift_d2   <= r_shift_d1;
        r_subtract   <= subtract_i;
            r_load_acc   <= load_acc_i;
            r_sat    <= r_sat;
            r_rnd    <= r_rnd;

        end
    end

    // Registered / non-registered input path select
    wire [NBITS_A-1:0]  a = register_inputs_i ? r_a : a_i;
    wire [NBITS_B-1:0]  b = register_inputs_i ? r_b : b_i;

    wire [5:0] acc_fir = register_inputs_i ? r_acc_fir : acc_fir_i;
    wire       unsigned_a = register_inputs_i ? r_unsigned_a : unsigned_a_i;
    wire       unsigned_b = register_inputs_i ? r_unsigned_b : unsigned_b_i;
    wire [2:0] feedback   = register_inputs_i ? r_feedback   : feedback_i;
    wire       load_acc   = register_inputs_i ? r_load_acc   : load_acc_i;
    wire       subtract   = register_inputs_i ? r_subtract   : subtract_i;
    wire       sat    = register_inputs_i ? r_sat : saturate_enable_i;
    wire       rnd    = register_inputs_i ? r_rnd : round_i;

    // Shift right control
    wire [5:0] shift_d1 = register_inputs_i ? r_shift_d1 : shift_right_i;
    wire [5:0] shift_d2 = output_select_i[1] ? shift_d1 : r_shift_d2;

    // Multiplier
    wire unsigned_mode = unsigned_a & unsigned_b;
    wire [NBITS_A-1:0] mult_a;
    assign mult_a = (feedback == 3'h0) ?   a :
                    (feedback == 3'h1) ?   a :
                    (feedback == 3'h2) ?   a :
                    (feedback == 3'h3) ?   acc[NBITS_A-1:0] :
                    (feedback == 3'h4) ?   coef_0_i :
                    (feedback == 3'h5) ?   coef_1_i :
                    (feedback == 3'h6) ?   coef_2_i :
                       coef_3_i;    // if feedback == 3'h7

    wire [NBITS_B-1:0] mult_b = (feedback == 2'h2) ? {NBITS_B{1'b0}}  : b;

    wire [NBITS_A-1:0] mult_sgn_a = mult_a[NBITS_A-1];
    wire [NBITS_A-1:0] mult_mag_a = (mult_sgn_a && !unsigned_a) ? (~mult_a + 1) : mult_a;
    wire [NBITS_B-1:0] mult_sgn_b = mult_b[NBITS_B-1];
    wire [NBITS_B-1:0] mult_mag_b = (mult_sgn_b && !unsigned_b) ? (~mult_b + 1) : mult_b;

    wire [NBITS_A+NBITS_B-1:0] mult_mag = mult_mag_a * mult_mag_b;
    wire mult_sgn = (mult_sgn_a && !unsigned_a) ^ (mult_sgn_b && !unsigned_b);

    wire [NBITS_A+NBITS_B-1:0] mult = (unsigned_a && unsigned_b) ?
        (mult_a * mult_b) : (mult_sgn ? (~mult_mag + 1) : mult_mag);

    // Sign extension
    wire [NBITS_ACC-1:0] mult_xtnd = unsigned_mode ?
        {{(NBITS_ACC-NBITS_A-NBITS_B){1'b0}},                    mult[NBITS_A+NBITS_B-1:0]} :
        {{(NBITS_ACC-NBITS_A-NBITS_B){mult[NBITS_A+NBITS_B-1]}}, mult[NBITS_A+NBITS_B-1:0]};

    // Adder
    wire [NBITS_ACC-1:0] acc_fir_int = unsigned_a ? {{(NBITS_ACC-NBITS_A){1'b0}},         a} :
                                                    {{(NBITS_ACC-NBITS_A){a[NBITS_A-1]}}, a} ;

    wire [NBITS_ACC-1:0] add_a = (subtract) ? (~mult_xtnd + 1) : mult_xtnd;
    wire [NBITS_ACC-1:0] add_b = (feedback_i == 3'h0) ? acc :
                                 (feedback_i == 3'h1) ? {{NBITS_ACC}{1'b0}} : (acc_fir_int << acc_fir);

    wire [NBITS_ACC-1:0] add_o = add_a + add_b;

    // Accumulator
    initial acc <= 0;

    always @(posedge clock_i or posedge s_reset)
        if (s_reset) acc <= 'h0;
        else begin
            if (load_acc)
                acc <= add_o;
            else
                acc <= acc;
        end

    // Adder/accumulator output selection
    wire [NBITS_ACC-1:0] acc_out = (output_select_i[1]) ? add_o : acc;

    // Round, shift, saturate
    wire [NBITS_ACC-1:0] acc_rnd = (rnd && (shift_right_i != 0)) ? (acc_out + ({{(NBITS_ACC-1){1'b0}}, 1'b1} << (shift_right_i - 1))) :
                                                                    acc_out;

    wire [NBITS_ACC-1:0] acc_shr = (unsigned_mode) ? (acc_rnd  >> shift_right_i) :
                                                     (acc_rnd >>> shift_right_i);

    wire [NBITS_ACC-1:0] acc_sat_u = (acc_shr[NBITS_ACC-1:NBITS_Z] != 0) ? {{(NBITS_ACC-NBITS_Z){1'b0}},{NBITS_Z{1'b1}}} :
                                                                           {{(NBITS_ACC-NBITS_Z){1'b0}},{acc_shr[NBITS_Z-1:0]}};

    wire [NBITS_ACC-1:0] acc_sat_s = ((|acc_shr[NBITS_ACC-1:NBITS_Z-1] == 1'b0) ||
                                      (&acc_shr[NBITS_ACC-1:NBITS_Z-1] == 1'b1)) ? {{(NBITS_ACC-NBITS_Z){1'b0}},{acc_shr[NBITS_Z-1:0]}} :
                                                                                   {{(NBITS_ACC-NBITS_Z){1'b0}},{acc_shr[NBITS_ACC-1],{NBITS_Z-1{~acc_shr[NBITS_ACC-1]}}}};

    wire [NBITS_ACC-1:0] acc_sat = (sat) ? ((unsigned_mode) ? acc_sat_u : acc_sat_s) : acc_shr;

    // Output signals
    wire [NBITS_Z-1:0]  z0;
    reg  [NBITS_Z-1:0]  z1;
    wire [NBITS_Z-1:0]  z2;

    assign z0 = mult_xtnd[NBITS_Z-1:0];
    assign z2 = acc_sat[NBITS_Z-1:0];

    initial z1 <= 0;

    always @(posedge clock_i or posedge s_reset)
        if (s_reset)
            z1 <= 0;
        else begin
            z1 <= (output_select_i == 3'b100) ? z0 : z2;
        end

    // Output mux
    assign z_o = (output_select_i == 3'h0) ?   z0 :
                 (output_select_i == 3'h1) ?   z2 :
                 (output_select_i == 3'h2) ?   z2 :
                 (output_select_i == 3'h3) ?   z2 :
                 (output_select_i == 3'h4) ?   z1 :
                 (output_select_i == 3'h5) ?   z1 :
                 (output_select_i == 3'h6) ?   z1 :
                           z1;  // if output_select_i == 3'h7

    // B input delayed passthrough
    initial dly_b_o <= 0;

    always @(posedge clock_i or posedge s_reset)
        if (s_reset)
            dly_b_o <= 0;
        else
            dly_b_o <= b_i;

endmodule

module dsp_t1_20x18x64 (
    input  wire [19:0] a_i,
    input  wire [17:0] b_i,
    input  wire [ 5:0] acc_fir_i,
    output wire [37:0] z_o,
    output wire [17:0] dly_b_o,

    (* clkbuf_sink *)
    input  wire        clock_i,
    input  wire        reset_i,

    input  wire [ 2:0] feedback_i,
    input  wire        load_acc_i,
    input  wire        unsigned_a_i,
    input  wire        unsigned_b_i,

    input  wire [ 2:0] output_select_i,
    input  wire        saturate_enable_i,
    input  wire [ 5:0] shift_right_i,
    input  wire        round_i,
    input  wire        subtract_i,
    input  wire        register_inputs_i
);

    parameter [19:0] COEFF_0 = 20'd0;
    parameter [19:0] COEFF_1 = 20'd0;
    parameter [19:0] COEFF_2 = 20'd0;
    parameter [19:0] COEFF_3 = 20'd0;

   QL_DSP2 #(
    .MODE_BITS({COEFF_3, COEFF_2, COEFF_1, COEFF_0})
   ) dsp (
    .a(a_i),
    .b(b_i),
    .z(z_o),
    .dly_b(dly_b_o),

    .f_mode(1'b0),  // 20x18x64 DSP

    .acc_fir(acc_fir_i),
    .feedback(feedback_i),
    .load_acc(load_acc_i),

    .unsigned_a(unsigned_a_i),
    .unsigned_b(unsigned_b_i),

    .clk(clock_i),
    .reset(reset_i),

    .saturate_enable(saturate_enable_i),
    .output_select(output_select_i),
    .round(round_i),
    .shift_right(shift_right_i),
    .subtract(subtract_i),
    .register_inputs(register_inputs_i)
    );
endmodule

module dsp_t1_10x9x32 (
    input  wire [ 9:0] a_i,
    input  wire [ 8:0] b_i,
    input  wire [ 5:0] acc_fir_i,
    output wire [18:0] z_o,
    output wire [ 8:0] dly_b_o,

    (* clkbuf_sink *)
    input  wire        clock_i,
    input  wire        reset_i,

    input  wire [ 2:0] feedback_i,
    input  wire        load_acc_i,
    input  wire        unsigned_a_i,
    input  wire        unsigned_b_i,

    input  wire [ 2:0] output_select_i,
    input  wire        saturate_enable_i,
    input  wire [ 5:0] shift_right_i,
    input  wire        round_i,
    input  wire        subtract_i,
    input  wire        register_inputs_i
);

    parameter [9:0] COEFF_0 = 10'd0;
    parameter [9:0] COEFF_1 = 10'd0;
    parameter [9:0] COEFF_2 = 10'd0;
    parameter [9:0] COEFF_3 = 10'd0;

    wire [18:0] z_rem;
    wire [8:0] dly_b_rem;

    QL_DSP2 #(
    .MODE_BITS({10'd0, COEFF_3,
                10'd0, COEFF_2,
                10'd0, COEFF_1,
                10'd0, COEFF_0})
   ) dsp (
    .a({10'd0, a_i}),
    .b({9'd0, b_i}),
    .z({z_rem, z_o}),
    .dly_b({dly_b_rem, dly_b_o}),

    .f_mode(1'b1),  // 10x9x32 DSP

    .acc_fir(acc_fir_i),
    .feedback(feedback_i),
    .load_acc(load_acc_i),

    .unsigned_a(unsigned_a_i),
    .unsigned_b(unsigned_b_i),

    .clk(clock_i),
    .reset(reset_i),

    .saturate_enable(saturate_enable_i),
    .output_select(output_select_i),
    .round(round_i),
    .shift_right(shift_right_i),
    .subtract(subtract_i),
    .register_inputs(register_inputs_i)
    );
endmodule