minitests/partial_reconfig_flow/Makefile

.PRECIOUS: harness_impl.dcp %_impl.dcp %.bit

# Top-level target for generating a programmable bitstream.  Given a .fasm
# file, calling make with the .fasm extension replaced with _hand_crafted.bit
# will generate a bitstream that includes both the harness and the .fasm design
# ready for programming to a board.  For example,
# 'make inv_hand_crafted.bit' will generate a bitstream that includes the
# design from roi_noninv.fasm. 
%_hand_crafted.bit: init_sequence.bit %_no_headers.bin final_sequence.bin
	cat $^ > $@

%_no_headers.bin: %_patched.bin
	# WARNING: these values need to be tweaked if anything about the
	# Vivado-generated design changes.
	xxd -p -s 0x18 $< | xxd -r -p - $@

%_patched.bin: %_roi_partial.frm harness.bit
	${XRAY_TOOLS_DIR}/xc7patch \
		--part_file ${XRAY_PART_YAML} \
		--bitstream_file harness.bit \
		--frm_file $< \
		--output_file $@

# xc7patch currently only generates the actual frame writes which is
# insufficient to program a device.  Grab the initialization and finalization
# sequences from the harness bitstream so they can be tacked on to the
# xc7patch-generated bitstream to create a programmable bitstream.
#
# The offsets used below were determined by manually inspecting
# harness.bit with a hex editor.  init_sequence.bit is the beginning of
# the file until just before the actual frame data is sent via a write to FDRI.
# final_sequence.bin is from just after the frame data write to the end of the
# file.  Note that final_sequence.bin normally includes at least one CRC check.
# The sed command replaces any CRC checks with a Reset CRC command which is the
# same behavior as setting BITSTREAM.GENERAL.CRC to Disabled.  These offset
# should not change unless you alter the bitstream format used (i.e. setting
# BITSTREAM.GENERAL.DEBUGBITSTREAM or BITSTREAM.GENERAL.PERFRAMECRC to YES).
init_sequence.bit: harness.bit
	# WARNING: these values need to be tweaked if anything about the
	# Vivado-generated design changes.
	xxd -p -l 0x147 $< | xxd -r -p - $@

final_sequence.bin: harness.bit
	# WARNING: these values need to be tweaked if anything about the
	# Vivado-generated design changes.
	xxd -p -s 0x216abf $< | \
		tr -d '\n' | \
		sed -e 's/30000001.\{8\}/3000800100000007/g' | \
		fold -w 40 | \
		xxd -r -p - $@

# Generate a suitable harness by using Vivado's partial reconfiguration
# feature.  inv.v is used as a sample reconfiguration design as one is
# required to generate a partial reconfiguration design.
harness_synth.dcp: harness_synthesize.tcl harness.v
	vivado -mode batch -source harness_synthesize.tcl

harness_impl.dcp: harness_synth.dcp inv_synth.dcp harness_implement.tcl
	vivado -mode batch -source harness_implement.tcl

# Synthesize an ROI design
%_synth.dcp: %.v roi_synthesize.tcl
	vivado -mode batch -source roi_synthesize.tcl -tclargs $< $@

# Implement an ROI design
%_impl.dcp: %_synth.dcp harness_impl.dcp roi_implement.tcl
	vivado -mode batch -source roi_implement.tcl -tclargs $< $@

# Generate bitstreams from an implemented design.  Two bitstreams are
# generated: one containing a complete design including the harness (.bit) and
# one that only contains the frames that implement the ROI design
# (_roi_partial.bit).
%.bit: %_impl.dcp write_bitstream.tcl
	vivado -mode batch -source write_bitstream.tcl -tclargs $< $@
%_roi_partial.bit: %.bit ;

# Conversions between various formats.
%.bits: %.bit
	${XRAY_BITREAD} -z -y -o $@ $<

%.segp: %.bits
	${XRAY_SEGPRINT} -zd $< > $@

%.fasm: %.segp
	${XRAY_DIR}/tools/segprint2fasm.py $< $@

%.frm: %.fasm
	${XRAY_DIR}/tools/fasm2frame.py $< $@

# This format is a human-readable representation of the configuration packets
# used to interact with 7-series chips over JTAG.
%.packets: %.bit
	${XRAY_TOOLS_DIR}/bittool list_config_packets $< > $@

clean:
	rm -rf vivado*.log vivado_*.str vivado*.jou design *.bits *.dcp *.bit design.txt .Xil
	rm -rf *.frm *.segp *.packets *.bin *.fasm
	rm -rf hd_visual

.PHONY: clean