| // DESCRIPTION: Verilator: Verilog Test module | |
| // | |
| // This file ONLY is placed into the Public Domain, for any use, | |
| // without warranty, 2017 by Wilson Snyder. | |
| module t (/*AUTOARG*/ | |
| // Inputs | |
| clk | |
| ); | |
| input clk; | |
| integer cyc=0; | |
| reg [63:0] crc; | |
| reg [63:0] sum; | |
| // Take CRC data and apply to testblock inputs | |
| wire [106:0] in = {~crc[42:0], crc[63:0]}; | |
| /*AUTOWIRE*/ | |
| // Beginning of automatic wires (for undeclared instantiated-module outputs) | |
| wire [7:0] out1; // From test of Test.v | |
| wire [7:0] out2; // From test of Test.v | |
| // End of automatics | |
| Test test (/*AUTOINST*/ | |
| // Outputs | |
| .out1 (out1[7:0]), | |
| .out2 (out2[7:0]), | |
| // Inputs | |
| .in (in[106:0])); | |
| // Aggregate outputs into a single result vector | |
| wire [63:0] result = {48'h0, out1, out1}; | |
| // Test loop | |
| always @ (posedge clk) begin | |
| `ifdef TEST_VERBOSE | |
| $write("[%0t] cyc==%0d crc=%x result=%x\n",$time, cyc, crc, result); | |
| `endif | |
| cyc <= cyc + 1; | |
| crc <= {crc[62:0], crc[63]^crc[2]^crc[0]}; | |
| sum <= result ^ {sum[62:0],sum[63]^sum[2]^sum[0]}; | |
| if (cyc==0) begin | |
| // Setup | |
| crc <= 64'h5aef0c8d_d70a4497; | |
| sum <= '0; | |
| end | |
| else if (cyc<10) begin | |
| sum <= '0; | |
| end | |
| else if (cyc<90) begin | |
| end | |
| else if (cyc==99) begin | |
| $write("[%0t] cyc==%0d crc=%x sum=%x\n",$time, cyc, crc, sum); | |
| if (crc !== 64'hc77bb9b3784ea091) $stop; | |
| // What checksum will we end up with (above print should match) | |
| `define EXPECTED_SUM 64'hc746017202a24ecc | |
| if (sum !== `EXPECTED_SUM) $stop; | |
| $write("*-* All Finished *-*\n"); | |
| $finish; | |
| end | |
| end | |
| endmodule | |
| module Test (/*AUTOARG*/ | |
| // Outputs | |
| out1, out2, | |
| // Inputs | |
| in | |
| ); | |
| // Replace this module with the device under test. | |
| // | |
| // Change the code in the t module to apply values to the inputs and | |
| // merge the output values into the result vector. | |
| input [106:0] in; | |
| output [7:0] out1, out2; | |
| // verilator lint_off WIDTH | |
| // Better written as onibble[99 +: 8]. Verilator will convert it. | |
| wire [7:0] out1 = (in >>> 99) & 255; | |
| // verilator lint_on WIDTH | |
| wire [7:0] out2 = in[106:99]; | |
| endmodule |