| /////////////////////////////////////////////////////////////////////////// | |
| // | |
| // To test: | |
| // (a) The use & representation of time variables | |
| // (b) The display of time variables | |
| // | |
| // Compile and run the program | |
| // iverilog tt_clean.v | |
| // vvp a.out | |
| // | |
| // VISUALLY INSPECT the displays. (There ain't no way to automate this) | |
| // | |
| /////////////////////////////////////////////////////////////////////////// | |
| `timescale 1 ns / 10 ps | |
| `define PCI_CLK_PERIOD 15.0 // 66 Mhz | |
| module top; | |
| reg PCI_Clk; | |
| reg fail; | |
| initial PCI_Clk <= 0; | |
| always #(`PCI_CLK_PERIOD/2) PCI_Clk <= ~PCI_Clk; | |
| initial begin | |
| fail = 0; | |
| $display("\n\t\t==> CHECK THIS DISPLAY ==> \n"); | |
| $display("pci_clk_period:\t\t\t %0d",`PCI_CLK_PERIOD); | |
| $display("pci_clk_period:\t\t\t %0t",`PCI_CLK_PERIOD); | |
| if($time !== 0) fail = 1; | |
| if (fail == 1) | |
| $display("$time=%0d (0)", $time); | |
| delay_pci(3); | |
| if($simtime !== 4500) fail = 1; | |
| if($time !== 45) fail = 1; | |
| if (fail == 1) | |
| $display("$time=%0d (45)", $time); | |
| #15; | |
| if($simtime !== 6000) fail = 1; | |
| if($time !== 60) fail = 1; | |
| #(`PCI_CLK_PERIOD); | |
| if($simtime !== 7500) fail = 1; | |
| if($time !== 75) fail = 1; | |
| #(`PCI_CLK_PERIOD *2); | |
| if($simtime !== 10500) fail = 1; | |
| if($time !== 105) fail = 1; | |
| $timeformat(-9,2,"ns",20); | |
| $display("after setting timeformat:"); | |
| $display("pci_clk_period:\t\t\t %0d",`PCI_CLK_PERIOD); | |
| $display("pci_clk_period:\t\t\t %0t",`PCI_CLK_PERIOD); | |
| delay_pci(3); | |
| if($simtime !== 15000) fail = 1; | |
| if($time !== 150) fail = 1; | |
| #15; | |
| if($simtime !== 16500) fail = 1; | |
| if($time !== 165) fail = 1; | |
| #(`PCI_CLK_PERIOD); | |
| if($simtime !== 18000) fail = 1; | |
| if($time !== 180) fail = 1; | |
| #(`PCI_CLK_PERIOD *2); | |
| if($simtime !== 21000) fail = 1; | |
| if($time !== 210) fail = 1; | |
| $display("\t\t**********************************************"); | |
| if(fail) $display("\t\t****** time representation test BAD *******"); | |
| else $display("\t\t****** time representation test OK *******"); | |
| $display("\t\t**********************************************\n"); | |
| $finish; | |
| end | |
| task delay_pci; | |
| input delta; | |
| integer delta; | |
| integer ii; | |
| begin | |
| #(`PCI_CLK_PERIOD * delta); | |
| end | |
| endtask | |
| endmodule | |