| // DESCRIPTION: Verilator: Verilog Test module | |
| // | |
| // Use this file as a template for submitting bugs, etc. | |
| // This module takes a single clock input, and should either | |
| // $write("*-* All Finished *-*\n"); | |
| // $finish; | |
| // on success, or $stop. | |
| // | |
| // The code as shown applies a random vector to the Test | |
| // module, then calculates a CRC on the Test module's outputs. | |
| // | |
| // **If you do not wish for your code to be released to the public | |
| // please note it here, otherwise:** | |
| // | |
| // This file ONLY is placed into the Public Domain, for any use, | |
| // without warranty, 2019 by ____YOUR_NAME_HERE____. | |
| module t (/*AUTOARG*/ | |
| // Inputs | |
| clk | |
| ); | |
| input clk; | |
| integer cyc=0; | |
| reg [63:0] crc; | |
| reg [63:0] sum; | |
| /*AUTOWIRE*/ | |
| // Beginning of automatic wires (for undeclared instantiated-module outputs) | |
| wire [31:0] result; // From test of Test.v | |
| // End of automatics | |
| Test test (.*); | |
| // Test loop | |
| always @ (posedge clk) begin | |
| `ifdef TEST_VERBOSE | |
| $write("[%0t] cyc==%0d crc=%x result=%x\n",$time, cyc, crc, result); | |
| `endif | |
| cyc <= cyc + 1; | |
| crc <= {crc[62:0], crc[63]^crc[2]^crc[0]}; | |
| sum <= result ^ {sum[62:0],sum[63]^sum[2]^sum[0]}; | |
| if (cyc==0) begin | |
| // Setup | |
| crc <= 64'h5aef0c8d_d70a4497; | |
| sum <= '0; | |
| end | |
| else if (cyc<10) begin | |
| sum <= '0; | |
| end | |
| else if (cyc<90) begin | |
| end | |
| else if (cyc==99) begin | |
| $write("[%0t] cyc==%0d crc=%x sum=%x\n",$time, cyc, crc, sum); | |
| if (crc !== 64'hc77bb9b3784ea091) $stop; | |
| // What checksum will we end up with (above print should match) | |
| `define EXPECTED_SUM 64'he58508de5310b541 | |
| if (sum !== `EXPECTED_SUM) $stop; | |
| $write("*-* All Finished *-*\n"); | |
| $finish; | |
| end | |
| end | |
| endmodule | |
| module Test | |
| ( | |
| input clk, | |
| input [63:0] crc, | |
| input [31:0] cyc, | |
| output wire [31:0] result); | |
| wire enable = crc[32]; | |
| wire [31:0] d = crc[31:0]; | |
| logic [31:0] y; | |
| always @(d iff enable == 1) begin | |
| y <= d; | |
| end | |
| wire reset = (cyc < 10); | |
| assert property (@(posedge clk iff enable) | |
| disable iff (reset) | |
| (crc != '0)); | |
| // Aggregate outputs into a single result vector | |
| assign result = {32'h0, y}; | |
| endmodule |