| // DESCRIPTION: Verilator: Verilog Test module | |
| // | |
| // This file ONLY is placed into the Public Domain, for any use, | |
| // without warranty, 2012 by Wilson Snyder. | |
| module t (/*AUTOARG*/ | |
| // Inputs | |
| clk | |
| ); | |
| input clk; | |
| integer cyc=0; | |
| reg [63:0] crc; | |
| reg [63:0] sum; | |
| // Take CRC data and apply to testblock inputs | |
| wire [31:0] in = crc[31:0]; | |
| localparam WIDTH = 31; | |
| /*AUTOWIRE*/ | |
| // Beginning of automatic wires (for undeclared instantiated-module outputs) | |
| wire [WIDTH-1:0] b; // From test of Test.v | |
| wire [WIDTH-1:0] c; // From test of Test.v | |
| // End of automatics | |
| reg rst_l; | |
| Test #(.WIDTH(WIDTH)) | |
| test (/*AUTOINST*/ | |
| // Outputs | |
| .b (b[WIDTH-1:0]), | |
| .c (c[WIDTH-1:0]), | |
| // Inputs | |
| .clk (clk), | |
| .rst_l (rst_l), | |
| .in (in[WIDTH-1:0])); | |
| // Aggregate outputs into a single result vector | |
| wire [63:0] result = {1'h0, c, 1'b0, b}; | |
| // Test loop | |
| always @ (posedge clk) begin | |
| `ifdef TEST_VERBOSE | |
| $write("[%0t] cyc==%0d crc=%x result=%x\n",$time, cyc, crc, result); | |
| `endif | |
| cyc <= cyc + 1; | |
| crc <= {crc[62:0], crc[63]^crc[2]^crc[0]}; | |
| sum <= result ^ {sum[62:0],sum[63]^sum[2]^sum[0]}; | |
| if (cyc==0) begin | |
| // Setup | |
| crc <= 64'h5aef0c8d_d70a4497; | |
| sum <= 64'h0; | |
| rst_l <= ~1'b1; | |
| end | |
| else if (cyc<10) begin | |
| sum <= 64'h0; | |
| rst_l <= ~1'b1; | |
| // Hold reset while summing | |
| end | |
| else if (cyc<20) begin | |
| rst_l <= ~1'b0; | |
| end | |
| else if (cyc<90) begin | |
| end | |
| else if (cyc==99) begin | |
| $write("[%0t] cyc==%0d crc=%x sum=%x\n",$time, cyc, crc, sum); | |
| if (crc !== 64'hc77bb9b3784ea091) $stop; | |
| // What checksum will we end up with (above print should match) | |
| `define EXPECTED_SUM 64'hbcfcebdb75ec9d32 | |
| if (sum !== `EXPECTED_SUM) $stop; | |
| $write("*-* All Finished *-*\n"); | |
| $finish; | |
| end | |
| end | |
| endmodule | |
| module Test (/*AUTOARG*/ | |
| // Outputs | |
| b, c, | |
| // Inputs | |
| clk, rst_l, in | |
| ); | |
| parameter WIDTH = 5; | |
| input clk; | |
| input rst_l; | |
| input [WIDTH-1:0] in; | |
| output wire [WIDTH-1:0] b; | |
| output wire [WIDTH-1:0] c; | |
| dff # ( .WIDTH (WIDTH), | |
| .RESET ('0), // Although this is a single bit, the parameter must be the specified type | |
| .RESET_WIDTH (1) ) | |
| sub1 | |
| ( .clk(clk), .rst_l(rst_l), .q(b), .d(in) ); | |
| dff # ( .WIDTH (WIDTH), | |
| .RESET ({ 1'b1, {(WIDTH-1){1'b0}} }), | |
| .RESET_WIDTH (WIDTH)) | |
| sub2 | |
| ( .clk(clk), .rst_l(rst_l), .q(c), .d(in) ); | |
| endmodule | |
| module dff (/*AUTOARG*/ | |
| // Outputs | |
| q, | |
| // Inputs | |
| clk, rst_l, d | |
| ); | |
| parameter WIDTH = 1; | |
| parameter RESET = {WIDTH{1'b0}}; | |
| parameter RESET_WIDTH = WIDTH; | |
| input clk; | |
| input rst_l; | |
| input [WIDTH-1:0] d; | |
| output reg [WIDTH-1:0] q; | |
| always_ff @(posedge clk or negedge rst_l) begin | |
| if ($bits(RESET) != RESET_WIDTH) $stop; | |
| // verilator lint_off WIDTH | |
| if (~rst_l) q <= RESET; | |
| // verilator lint_on WIDTH | |
| else q <= d; | |
| end | |
| endmodule |