| //---------------------------------------------------------------------------- | |
| // Copyright (C) 2009 , Olivier Girard | |
| // | |
| // Redistribution and use in source and binary forms, with or without | |
| // modification, are permitted provided that the following conditions | |
| // are met: | |
| // * Redistributions of source code must retain the above copyright | |
| // notice, this list of conditions and the following disclaimer. | |
| // * Redistributions in binary form must reproduce the above copyright | |
| // notice, this list of conditions and the following disclaimer in the | |
| // documentation and/or other materials provided with the distribution. | |
| // * Neither the name of the authors nor the names of its contributors | |
| // may be used to endorse or promote products derived from this software | |
| // without specific prior written permission. | |
| // | |
| // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
| // AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
| // IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE | |
| // ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE | |
| // LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, | |
| // OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF | |
| // SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS | |
| // INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN | |
| // CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) | |
| // ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF | |
| // THE POSSIBILITY OF SUCH DAMAGE | |
| // | |
| //---------------------------------------------------------------------------- | |
| // | |
| // *File Name: openMSP430_defines.v | |
| // | |
| // *Module Description: | |
| // openMSP430 Configuration file | |
| // | |
| // *Author(s): | |
| // - Olivier Girard, olgirard@gmail.com | |
| // | |
| //---------------------------------------------------------------------------- | |
| // $Rev: 180 $ | |
| // $LastChangedBy: olivier.girard $ | |
| // $LastChangedDate: 2013-02-25 22:23:18 +0100 (Mon, 25 Feb 2013) $ | |
| //---------------------------------------------------------------------------- | |
| //`define OMSP_NO_INCLUDE | |
| `ifdef OMSP_NO_INCLUDE | |
| `else | |
| `include "openMSP430_undefines.v" | |
| `endif | |
| //============================================================================ | |
| //============================================================================ | |
| // BASIC SYSTEM CONFIGURATION | |
| //============================================================================ | |
| //============================================================================ | |
| // | |
| // Note: the sum of program, data and peripheral memory spaces must not | |
| // exceed 64 kB | |
| // | |
| // Program Memory Size: | |
| // Uncomment the required memory size | |
| //------------------------------------------------------- | |
| //`define PMEM_SIZE_CUSTOM | |
| //`define PMEM_SIZE_59_KB | |
| //`define PMEM_SIZE_55_KB | |
| //`define PMEM_SIZE_54_KB | |
| //`define PMEM_SIZE_51_KB | |
| //`define PMEM_SIZE_48_KB | |
| //`define PMEM_SIZE_41_KB | |
| //`define PMEM_SIZE_32_KB | |
| //`define PMEM_SIZE_24_KB | |
| //`define PMEM_SIZE_16_KB | |
| //`define PMEM_SIZE_12_KB | |
| //`define PMEM_SIZE_8_KB | |
| //`define PMEM_SIZE_4_KB | |
| `define PMEM_SIZE_2_KB | |
| //`define PMEM_SIZE_1_KB | |
| // Data Memory Size: | |
| // Uncomment the required memory size | |
| //------------------------------------------------------- | |
| //`define DMEM_SIZE_CUSTOM | |
| //`define DMEM_SIZE_32_KB | |
| //`define DMEM_SIZE_24_KB | |
| //`define DMEM_SIZE_16_KB | |
| //`define DMEM_SIZE_10_KB | |
| //`define DMEM_SIZE_8_KB | |
| //`define DMEM_SIZE_5_KB | |
| //`define DMEM_SIZE_4_KB | |
| //`define DMEM_SIZE_2p5_KB | |
| //`define DMEM_SIZE_2_KB | |
| //`define DMEM_SIZE_1_KB | |
| //`define DMEM_SIZE_512_B | |
| //`define DMEM_SIZE_256_B | |
| `define DMEM_SIZE_128_B | |
| // Include/Exclude Hardware Multiplier | |
| `define MULTIPLIER | |
| // Include/Exclude Serial Debug interface | |
| `define DBG_EN | |
| //============================================================================ | |
| //============================================================================ | |
| // ADVANCED SYSTEM CONFIGURATION (FOR EXPERIENCED USERS) | |
| //============================================================================ | |
| //============================================================================ | |
| //------------------------------------------------------- | |
| // Custom user version number | |
| //------------------------------------------------------- | |
| // This 5 bit field can be freely used in order to allow | |
| // custom identification of the system through the debug | |
| // interface. | |
| // (see CPU_ID.USER_VERSION field in the documentation) | |
| //------------------------------------------------------- | |
| `define USER_VERSION 5'b00000 | |
| //------------------------------------------------------- | |
| // Include/Exclude Watchdog timer | |
| //------------------------------------------------------- | |
| // When excluded, the following functionality will be | |
| // lost: | |
| // - Watchog (both interval and watchdog modes) | |
| // - NMI interrupt edge selection | |
| // - Possibility to generate a software PUC reset | |
| //------------------------------------------------------- | |
| `define WATCHDOG | |
| //------------------------------------------------------- | |
| // Include/Exclude Non-Maskable-Interrupt support | |
| //------------------------------------------------------- | |
| `define NMI | |
| //------------------------------------------------------- | |
| // Input synchronizers | |
| //------------------------------------------------------- | |
| // In some cases, the asynchronous input ports might | |
| // already be synchronized externally. | |
| // If an extensive CDC design review showed that this | |
| // is really the case, the individual synchronizers | |
| // can be disabled with the following defines. | |
| // | |
| // Notes: | |
| // - all three signals are all sampled in the MCLK domain | |
| // | |
| // - the dbg_en signal reset the debug interface | |
| // when 0. Therefore make sure it is glitch free. | |
| // | |
| //------------------------------------------------------- | |
| `define SYNC_NMI | |
| //`define SYNC_CPU_EN | |
| //`define SYNC_DBG_EN | |
| //------------------------------------------------------- | |
| // Peripheral Memory Space: | |
| //------------------------------------------------------- | |
| // The original MSP430 architecture map the peripherals | |
| // from 0x0000 to 0x01FF (i.e. 512B of the memory space). | |
| // The following defines allow you to expand this space | |
| // up to 32 kB (i.e. from 0x0000 to 0x7fff). | |
| // As a consequence, the data memory mapping will be | |
| // shifted up and a custom linker script will therefore | |
| // be required by the GCC compiler. | |
| //------------------------------------------------------- | |
| //`define PER_SIZE_CUSTOM | |
| //`define PER_SIZE_32_KB | |
| //`define PER_SIZE_16_KB | |
| //`define PER_SIZE_8_KB | |
| //`define PER_SIZE_4_KB | |
| //`define PER_SIZE_2_KB | |
| //`define PER_SIZE_1_KB | |
| `define PER_SIZE_512_B | |
| //------------------------------------------------------- | |
| // Defines the debugger CPU_CTL.RST_BRK_EN reset value | |
| // (CPU break on PUC reset) | |
| //------------------------------------------------------- | |
| // When defined, the CPU will automatically break after | |
| // a PUC occurrence by default. This is typically useful | |
| // when the program memory can only be initialized through | |
| // the serial debug interface. | |
| //------------------------------------------------------- | |
| `define DBG_RST_BRK_EN | |
| //============================================================================ | |
| //============================================================================ | |
| // EXPERT SYSTEM CONFIGURATION ( !!!! EXPERTS ONLY !!!! ) | |
| //============================================================================ | |
| //============================================================================ | |
| // | |
| // IMPORTANT NOTE: Please update following configuration options ONLY if | |
| // you have a good reason to do so... and if you know what | |
| // you are doing :-P | |
| // | |
| //============================================================================ | |
| //------------------------------------------------------- | |
| // Select serial debug interface protocol | |
| //------------------------------------------------------- | |
| // DBG_UART -> Enable UART (8N1) debug interface | |
| // DBG_I2C -> Enable I2C debug interface | |
| //------------------------------------------------------- | |
| `define DBG_UART | |
| //`define DBG_I2C | |
| //------------------------------------------------------- | |
| // Enable the I2C broadcast address | |
| //------------------------------------------------------- | |
| // For multicore systems, a common I2C broadcast address | |
| // can be given to all oMSP cores in order to | |
| // synchronously RESET, START, STOP, or STEP all CPUs | |
| // at once with a single I2C command. | |
| // If you have a single openMSP430 in your system, | |
| // this option can stay commented-out. | |
| //------------------------------------------------------- | |
| //`define DBG_I2C_BROADCAST | |
| //------------------------------------------------------- | |
| // Number of hardware breakpoint/watchpoint units | |
| // (each unit contains two hardware addresses available | |
| // for breakpoints or watchpoints): | |
| // - DBG_HWBRK_0 -> Include hardware breakpoints unit 0 | |
| // - DBG_HWBRK_1 -> Include hardware breakpoints unit 1 | |
| // - DBG_HWBRK_2 -> Include hardware breakpoints unit 2 | |
| // - DBG_HWBRK_3 -> Include hardware breakpoints unit 3 | |
| //------------------------------------------------------- | |
| // Please keep in mind that hardware breakpoints only | |
| // make sense whenever the program memory is not an SRAM | |
| // (i.e. Flash/OTP/ROM/...) or when you are interested | |
| // in data breakpoints. | |
| //------------------------------------------------------- | |
| //`define DBG_HWBRK_0 | |
| //`define DBG_HWBRK_1 | |
| //`define DBG_HWBRK_2 | |
| //`define DBG_HWBRK_3 | |
| //------------------------------------------------------- | |
| // Enable/Disable the hardware breakpoint RANGE mode | |
| //------------------------------------------------------- | |
| // When enabled this feature allows the hardware breakpoint | |
| // units to stop the cpu whenever an instruction or data | |
| // access lays within an address range. | |
| // Note that this feature is not supported by GDB. | |
| //------------------------------------------------------- | |
| //`define DBG_HWBRK_RANGE | |
| //------------------------------------------------------- | |
| // Custom Program/Data and Peripheral Memory Spaces | |
| //------------------------------------------------------- | |
| // The following values are valid only if the | |
| // corresponding *_SIZE_CUSTOM defines are uncommented: | |
| // | |
| // - *_SIZE : size of the section in bytes. | |
| // - *_AWIDTH : address port width, this value must allow | |
| // to address all WORDS of the section | |
| // (i.e. the *_SIZE divided by 2) | |
| //------------------------------------------------------- | |
| // Custom Program memory (enabled with PMEM_SIZE_CUSTOM) | |
| `define PMEM_CUSTOM_AWIDTH 10 | |
| `define PMEM_CUSTOM_SIZE 2048 | |
| // Custom Data memory (enabled with DMEM_SIZE_CUSTOM) | |
| `define DMEM_CUSTOM_AWIDTH 6 | |
| `define DMEM_CUSTOM_SIZE 128 | |
| // Custom Peripheral memory (enabled with PER_SIZE_CUSTOM) | |
| `define PER_CUSTOM_AWIDTH 8 | |
| `define PER_CUSTOM_SIZE 512 | |
| //------------------------------------------------------- | |
| // ASIC version | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // ASIC system configuration section (see below) and | |
| // will activate scan support for production test. | |
| // | |
| // WARNING: if you target an FPGA, leave this define | |
| // commented. | |
| //------------------------------------------------------- | |
| //`define ASIC | |
| //============================================================================ | |
| //============================================================================ | |
| // ASIC SYSTEM CONFIGURATION ( !!!! EXPERTS/PROFESSIONALS ONLY !!!! ) | |
| //============================================================================ | |
| //============================================================================ | |
| `ifdef ASIC | |
| //=============================================================== | |
| // FINE GRAINED CLOCK GATING | |
| //=============================================================== | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the fine | |
| // grained clock gating of all registers in the core. | |
| //------------------------------------------------------- | |
| `define CLOCK_GATING | |
| //=============================================================== | |
| // ASIC CLOCKING | |
| //=============================================================== | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the ASIC | |
| // architectural clock gating as well as the advanced low | |
| // power modes support (most common). | |
| // Comment this out in order to get FPGA-like clocking. | |
| //------------------------------------------------------- | |
| `define ASIC_CLOCKING | |
| `ifdef ASIC_CLOCKING | |
| //=============================================================== | |
| // LFXT CLOCK DOMAIN | |
| //=============================================================== | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the lfxt_clk | |
| // clock domain. | |
| // When commented out, the whole chip is clocked with dco_clk. | |
| //------------------------------------------------------- | |
| `define LFXT_DOMAIN | |
| //=============================================================== | |
| // CLOCK MUXES | |
| //=============================================================== | |
| //------------------------------------------------------- | |
| // MCLK: Clock Mux | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // MCLK clock MUX allowing the selection between | |
| // DCO_CLK and LFXT_CLK with the BCSCTL2.SELMx register. | |
| // When commented, DCO_CLK is selected. | |
| //------------------------------------------------------- | |
| `define MCLK_MUX | |
| //------------------------------------------------------- | |
| // SMCLK: Clock Mux | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // SMCLK clock MUX allowing the selection between | |
| // DCO_CLK and LFXT_CLK with the BCSCTL2.SELS register. | |
| // When commented, DCO_CLK is selected. | |
| //------------------------------------------------------- | |
| `define SMCLK_MUX | |
| //------------------------------------------------------- | |
| // WATCHDOG: Clock Mux | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // Watchdog clock MUX allowing the selection between | |
| // ACLK and SMCLK with the WDTCTL.WDTSSEL register. | |
| // When commented out, ACLK is selected if the | |
| // WATCHDOG_NOMUX_ACLK define is uncommented, SMCLK is | |
| // selected otherwise. | |
| //------------------------------------------------------- | |
| `define WATCHDOG_MUX | |
| //`define WATCHDOG_NOMUX_ACLK | |
| //=============================================================== | |
| // CLOCK DIVIDERS | |
| //=============================================================== | |
| //------------------------------------------------------- | |
| // MCLK: Clock divider | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // MCLK clock divider (/1/2/4/8) | |
| //------------------------------------------------------- | |
| `define MCLK_DIVIDER | |
| //------------------------------------------------------- | |
| // SMCLK: Clock divider (/1/2/4/8) | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // SMCLK clock divider | |
| //------------------------------------------------------- | |
| `define SMCLK_DIVIDER | |
| //------------------------------------------------------- | |
| // ACLK: Clock divider (/1/2/4/8) | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // ACLK clock divider | |
| //------------------------------------------------------- | |
| `define ACLK_DIVIDER | |
| //=============================================================== | |
| // LOW POWER MODES | |
| //=============================================================== | |
| //------------------------------------------------------- | |
| // LOW POWER MODE: CPUOFF | |
| //------------------------------------------------------- | |
| // When uncommented, this define will include the | |
| // clock gate allowing to switch off MCLK in | |
| // all low power modes: LPM0, LPM1, LPM2, LPM3, LPM4 | |
| //------------------------------------------------------- | |
| `define CPUOFF_EN | |
| //------------------------------------------------------- | |
| // LOW POWER MODE: SCG0 | |
| //------------------------------------------------------- | |
| // When uncommented, this define will enable the | |
| // DCO_ENABLE/WKUP port control (always 1 when commented). | |
| // This allows to switch off the DCO oscillator in the | |
| // following low power modes: LPM1, LPM3, LPM4 | |
| //------------------------------------------------------- | |
| `define SCG0_EN | |
| //------------------------------------------------------- | |
| // LOW POWER MODE: SCG1 | |
| //------------------------------------------------------- | |
| // When uncommented, this define will include the | |
| // clock gate allowing to switch off SMCLK in | |
| // the following low power modes: LPM2, LPM3, LPM4 | |
| //------------------------------------------------------- | |
| `define SCG1_EN | |
| //------------------------------------------------------- | |
| // LOW POWER MODE: OSCOFF | |
| //------------------------------------------------------- | |
| // When uncommented, this define will include the | |
| // LFXT_CLK clock gate and enable the LFXT_ENABLE/WKUP | |
| // port control (always 1 when commented). | |
| // This allows to switch off the low frequency oscillator | |
| // in the following low power modes: LPM4 | |
| //------------------------------------------------------- | |
| `define OSCOFF_EN | |
| `endif | |
| `endif | |
| //==========================================================================// | |
| //==========================================================================// | |
| //==========================================================================// | |
| //==========================================================================// | |
| //===== SYSTEM CONSTANTS --- !!!!!!!! DO NOT EDIT !!!!!!!! =====// | |
| //==========================================================================// | |
| //==========================================================================// | |
| //==========================================================================// | |
| //==========================================================================// | |
| // | |
| // PROGRAM, DATA & PERIPHERAL MEMORY CONFIGURATION | |
| //================================================== | |
| // Program Memory Size | |
| `ifdef PMEM_SIZE_59_KB | |
| `define PMEM_AWIDTH 15 | |
| `define PMEM_SIZE 60416 | |
| `endif | |
| `ifdef PMEM_SIZE_55_KB | |
| `define PMEM_AWIDTH 15 | |
| `define PMEM_SIZE 56320 | |
| `endif | |
| `ifdef PMEM_SIZE_54_KB | |
| `define PMEM_AWIDTH 15 | |
| `define PMEM_SIZE 55296 | |
| `endif | |
| `ifdef PMEM_SIZE_51_KB | |
| `define PMEM_AWIDTH 15 | |
| `define PMEM_SIZE 52224 | |
| `endif | |
| `ifdef PMEM_SIZE_48_KB | |
| `define PMEM_AWIDTH 15 | |
| `define PMEM_SIZE 49152 | |
| `endif | |
| `ifdef PMEM_SIZE_41_KB | |
| `define PMEM_AWIDTH 15 | |
| `define PMEM_SIZE 41984 | |
| `endif | |
| `ifdef PMEM_SIZE_32_KB | |
| `define PMEM_AWIDTH 14 | |
| `define PMEM_SIZE 32768 | |
| `endif | |
| `ifdef PMEM_SIZE_24_KB | |
| `define PMEM_AWIDTH 14 | |
| `define PMEM_SIZE 24576 | |
| `endif | |
| `ifdef PMEM_SIZE_16_KB | |
| `define PMEM_AWIDTH 13 | |
| `define PMEM_SIZE 16384 | |
| `endif | |
| `ifdef PMEM_SIZE_12_KB | |
| `define PMEM_AWIDTH 13 | |
| `define PMEM_SIZE 12288 | |
| `endif | |
| `ifdef PMEM_SIZE_8_KB | |
| `define PMEM_AWIDTH 12 | |
| `define PMEM_SIZE 8192 | |
| `endif | |
| `ifdef PMEM_SIZE_4_KB | |
| `define PMEM_AWIDTH 11 | |
| `define PMEM_SIZE 4096 | |
| `endif | |
| `ifdef PMEM_SIZE_2_KB | |
| `define PMEM_AWIDTH 10 | |
| `define PMEM_SIZE 2048 | |
| `endif | |
| `ifdef PMEM_SIZE_1_KB | |
| `define PMEM_AWIDTH 9 | |
| `define PMEM_SIZE 1024 | |
| `endif | |
| `ifdef PMEM_SIZE_CUSTOM | |
| `define PMEM_AWIDTH `PMEM_CUSTOM_AWIDTH | |
| `define PMEM_SIZE `PMEM_CUSTOM_SIZE | |
| `endif | |
| // Data Memory Size | |
| `ifdef DMEM_SIZE_32_KB | |
| `define DMEM_AWIDTH 14 | |
| `define DMEM_SIZE 32768 | |
| `endif | |
| `ifdef DMEM_SIZE_24_KB | |
| `define DMEM_AWIDTH 14 | |
| `define DMEM_SIZE 24576 | |
| `endif | |
| `ifdef DMEM_SIZE_16_KB | |
| `define DMEM_AWIDTH 13 | |
| `define DMEM_SIZE 16384 | |
| `endif | |
| `ifdef DMEM_SIZE_10_KB | |
| `define DMEM_AWIDTH 13 | |
| `define DMEM_SIZE 10240 | |
| `endif | |
| `ifdef DMEM_SIZE_8_KB | |
| `define DMEM_AWIDTH 12 | |
| `define DMEM_SIZE 8192 | |
| `endif | |
| `ifdef DMEM_SIZE_5_KB | |
| `define DMEM_AWIDTH 12 | |
| `define DMEM_SIZE 5120 | |
| `endif | |
| `ifdef DMEM_SIZE_4_KB | |
| `define DMEM_AWIDTH 11 | |
| `define DMEM_SIZE 4096 | |
| `endif | |
| `ifdef DMEM_SIZE_2p5_KB | |
| `define DMEM_AWIDTH 11 | |
| `define DMEM_SIZE 2560 | |
| `endif | |
| `ifdef DMEM_SIZE_2_KB | |
| `define DMEM_AWIDTH 10 | |
| `define DMEM_SIZE 2048 | |
| `endif | |
| `ifdef DMEM_SIZE_1_KB | |
| `define DMEM_AWIDTH 9 | |
| `define DMEM_SIZE 1024 | |
| `endif | |
| `ifdef DMEM_SIZE_512_B | |
| `define DMEM_AWIDTH 8 | |
| `define DMEM_SIZE 512 | |
| `endif | |
| `ifdef DMEM_SIZE_256_B | |
| `define DMEM_AWIDTH 7 | |
| `define DMEM_SIZE 256 | |
| `endif | |
| `ifdef DMEM_SIZE_128_B | |
| `define DMEM_AWIDTH 6 | |
| `define DMEM_SIZE 128 | |
| `endif | |
| `ifdef DMEM_SIZE_CUSTOM | |
| `define DMEM_AWIDTH `DMEM_CUSTOM_AWIDTH | |
| `define DMEM_SIZE `DMEM_CUSTOM_SIZE | |
| `endif | |
| // Peripheral Memory Size | |
| `ifdef PER_SIZE_32_KB | |
| `define PER_AWIDTH 14 | |
| `define PER_SIZE 32768 | |
| `endif | |
| `ifdef PER_SIZE_16_KB | |
| `define PER_AWIDTH 13 | |
| `define PER_SIZE 16384 | |
| `endif | |
| `ifdef PER_SIZE_8_KB | |
| `define PER_AWIDTH 12 | |
| `define PER_SIZE 8192 | |
| `endif | |
| `ifdef PER_SIZE_4_KB | |
| `define PER_AWIDTH 11 | |
| `define PER_SIZE 4096 | |
| `endif | |
| `ifdef PER_SIZE_2_KB | |
| `define PER_AWIDTH 10 | |
| `define PER_SIZE 2048 | |
| `endif | |
| `ifdef PER_SIZE_1_KB | |
| `define PER_AWIDTH 9 | |
| `define PER_SIZE 1024 | |
| `endif | |
| `ifdef PER_SIZE_512_B | |
| `define PER_AWIDTH 8 | |
| `define PER_SIZE 512 | |
| `endif | |
| `ifdef PER_SIZE_CUSTOM | |
| `define PER_AWIDTH `PER_CUSTOM_AWIDTH | |
| `define PER_SIZE `PER_CUSTOM_SIZE | |
| `endif | |
| // Data Memory Base Adresses | |
| `define DMEM_BASE `PER_SIZE | |
| // Program & Data Memory most significant address bit (for 16 bit words) | |
| `define PMEM_MSB `PMEM_AWIDTH-1 | |
| `define DMEM_MSB `DMEM_AWIDTH-1 | |
| `define PER_MSB `PER_AWIDTH-1 | |
| // | |
| // STATES, REGISTER FIELDS, ... | |
| //====================================== | |
| // Instructions type | |
| `define INST_SO 0 | |
| `define INST_JMP 1 | |
| `define INST_TO 2 | |
| // Single-operand arithmetic | |
| `define RRC 0 | |
| `define SWPB 1 | |
| `define RRA 2 | |
| `define SXT 3 | |
| `define PUSH 4 | |
| `define CALL 5 | |
| `define RETI 6 | |
| `define IRQ 7 | |
| // Conditional jump | |
| `define JNE 0 | |
| `define JEQ 1 | |
| `define JNC 2 | |
| `define JC 3 | |
| `define JN 4 | |
| `define JGE 5 | |
| `define JL 6 | |
| `define JMP 7 | |
| // Two-operand arithmetic | |
| `define MOV 0 | |
| `define ADD 1 | |
| `define ADDC 2 | |
| `define SUBC 3 | |
| `define SUB 4 | |
| `define CMP 5 | |
| `define DADD 6 | |
| `define BIT 7 | |
| `define BIC 8 | |
| `define BIS 9 | |
| `define XOR 10 | |
| `define AND 11 | |
| // Addressing modes | |
| `define DIR 0 | |
| `define IDX 1 | |
| `define INDIR 2 | |
| `define INDIR_I 3 | |
| `define SYMB 4 | |
| `define IMM 5 | |
| `define ABS 6 | |
| `define CONST 7 | |
| // Instruction state machine | |
| `define I_IRQ_FETCH 3'h0 | |
| `define I_IRQ_DONE 3'h1 | |
| `define I_DEC 3'h2 | |
| `define I_EXT1 3'h3 | |
| `define I_EXT2 3'h4 | |
| `define I_IDLE 3'h5 | |
| // Execution state machine | |
| // (swapped E_IRQ_0 and E_IRQ_2 values to suppress glitch generation warning from lint tool) | |
| `define E_IRQ_0 4'h2 | |
| `define E_IRQ_1 4'h1 | |
| `define E_IRQ_2 4'h0 | |
| `define E_IRQ_3 4'h3 | |
| `define E_IRQ_4 4'h4 | |
| `define E_SRC_AD 4'h5 | |
| `define E_SRC_RD 4'h6 | |
| `define E_SRC_WR 4'h7 | |
| `define E_DST_AD 4'h8 | |
| `define E_DST_RD 4'h9 | |
| `define E_DST_WR 4'hA | |
| `define E_EXEC 4'hB | |
| `define E_JUMP 4'hC | |
| `define E_IDLE 4'hD | |
| // ALU control signals | |
| `define ALU_SRC_INV 0 | |
| `define ALU_INC 1 | |
| `define ALU_INC_C 2 | |
| `define ALU_ADD 3 | |
| `define ALU_AND 4 | |
| `define ALU_OR 5 | |
| `define ALU_XOR 6 | |
| `define ALU_DADD 7 | |
| `define ALU_STAT_7 8 | |
| `define ALU_STAT_F 9 | |
| `define ALU_SHIFT 10 | |
| `define EXEC_NO_WR 11 | |
| // Debug interface | |
| `define DBG_UART_WR 18 | |
| `define DBG_UART_BW 17 | |
| `define DBG_UART_ADDR 16:11 | |
| // Debug interface CPU_CTL register | |
| `define HALT 0 | |
| `define RUN 1 | |
| `define ISTEP 2 | |
| `define SW_BRK_EN 3 | |
| `define FRZ_BRK_EN 4 | |
| `define RST_BRK_EN 5 | |
| `define CPU_RST 6 | |
| // Debug interface CPU_STAT register | |
| `define HALT_RUN 0 | |
| `define PUC_PND 1 | |
| `define SWBRK_PND 3 | |
| `define HWBRK0_PND 4 | |
| `define HWBRK1_PND 5 | |
| // Debug interface BRKx_CTL register | |
| `define BRK_MODE_RD 0 | |
| `define BRK_MODE_WR 1 | |
| `define BRK_MODE 1:0 | |
| `define BRK_EN 2 | |
| `define BRK_I_EN 3 | |
| `define BRK_RANGE 4 | |
| // Basic clock module: BCSCTL1 Control Register | |
| `define DIVAx 5:4 | |
| // Basic clock module: BCSCTL2 Control Register | |
| `define SELMx 7 | |
| `define DIVMx 5:4 | |
| `define SELS 3 | |
| `define DIVSx 2:1 | |
| // MCLK Clock gate | |
| `ifdef CPUOFF_EN | |
| `define MCLK_CGATE | |
| `else | |
| `ifdef MCLK_DIVIDER | |
| `define MCLK_CGATE | |
| `endif | |
| `endif | |
| // SMCLK Clock gate | |
| `ifdef SCG1_EN | |
| `define SMCLK_CGATE | |
| `else | |
| `ifdef SMCLK_DIVIDER | |
| `define SMCLK_CGATE | |
| `endif | |
| `endif | |
| // | |
| // DEBUG INTERFACE EXTRA CONFIGURATION | |
| //====================================== | |
| // Debug interface: CPU version | |
| `define CPU_VERSION 3'h2 | |
| // Debug interface: Software breakpoint opcode | |
| `define DBG_SWBRK_OP 16'h4343 | |
| // Debug UART interface auto data synchronization | |
| // If the following define is commented out, then | |
| // the DBG_UART_BAUD and DBG_DCO_FREQ need to be properly | |
| // defined. | |
| `define DBG_UART_AUTO_SYNC | |
| // Debug UART interface data rate | |
| // In order to properly setup the UART debug interface, you | |
| // need to specify the DCO_CLK frequency (DBG_DCO_FREQ) and | |
| // the chosen BAUD rate from the UART interface. | |
| // | |
| //`define DBG_UART_BAUD 9600 | |
| //`define DBG_UART_BAUD 19200 | |
| //`define DBG_UART_BAUD 38400 | |
| //`define DBG_UART_BAUD 57600 | |
| //`define DBG_UART_BAUD 115200 | |
| //`define DBG_UART_BAUD 230400 | |
| //`define DBG_UART_BAUD 460800 | |
| //`define DBG_UART_BAUD 576000 | |
| //`define DBG_UART_BAUD 921600 | |
| `define DBG_UART_BAUD 2000000 | |
| `define DBG_DCO_FREQ 20000000 | |
| `define DBG_UART_CNT ((`DBG_DCO_FREQ/`DBG_UART_BAUD)-1) | |
| // Debug interface input synchronizer | |
| `define SYNC_DBG_UART_RXD | |
| // Enable/Disable the hardware breakpoint RANGE mode | |
| `ifdef DBG_HWBRK_RANGE | |
| `define HWBRK_RANGE 1'b1 | |
| `else | |
| `define HWBRK_RANGE 1'b0 | |
| `endif | |
| // Counter width for the debug interface UART | |
| `define DBG_UART_XFER_CNT_W 16 | |
| // Check configuration | |
| `ifdef DBG_EN | |
| `ifdef DBG_UART | |
| `ifdef DBG_I2C | |
| CONFIGURATION ERROR: I2C AND UART DEBUG INTERFACE ARE BOTH ENABLED | |
| `endif | |
| `else | |
| `ifdef DBG_I2C | |
| `else | |
| CONFIGURATION ERROR: I2C OR UART DEBUG INTERFACE SHOULD BE ENABLED | |
| `endif | |
| `endif | |
| `endif | |
| // | |
| // MULTIPLIER CONFIGURATION | |
| //====================================== | |
| // If uncommented, the following define selects | |
| // the 16x16 multiplier (1 cycle) instead of the | |
| // default 16x8 multplier (2 cycles) | |
| //`define MPY_16x16 | |
| //====================================== | |
| // CONFIGURATION CHECKS | |
| //====================================== | |
| `ifdef LFXT_DOMAIN | |
| `else | |
| `ifdef MCLK_MUX | |
| CONFIGURATION ERROR: THE MCLK_MUX CAN ONLY BE ENABLED IF THE LFXT_DOMAIN IS ENABLED AS WELL | |
| `endif | |
| `ifdef SMCLK_MUX | |
| CONFIGURATION ERROR: THE SMCLK_MUX CAN ONLY BE ENABLED IF THE LFXT_DOMAIN IS ENABLED AS WELL | |
| `endif | |
| `ifdef WATCHDOG_MUX | |
| CONFIGURATION ERROR: THE WATCHDOG_MUX CAN ONLY BE ENABLED IF THE LFXT_DOMAIN IS ENABLED AS WELL | |
| `else | |
| `ifdef WATCHDOG_NOMUX_ACLK | |
| CONFIGURATION ERROR: THE WATCHDOG_NOMUX_ACLK CAN ONLY BE ENABLED IF THE LFXT_DOMAIN IS ENABLED AS WELL | |
| `endif | |
| `endif | |
| `ifdef OSCOFF_EN | |
| CONFIGURATION ERROR: THE OSCOFF LOW POWER MODE CAN ONLY BE ENABLED IF THE LFXT_DOMAIN IS ENABLED AS WELL | |
| `endif | |
| `endif |