| //---------------------------------------------------------------------------- | |
| // Copyright (C) 2009 , Olivier Girard | |
| // | |
| // Redistribution and use in source and binary forms, with or without | |
| // modification, are permitted provided that the following conditions | |
| // are met: | |
| // * Redistributions of source code must retain the above copyright | |
| // notice, this list of conditions and the following disclaimer. | |
| // * Redistributions in binary form must reproduce the above copyright | |
| // notice, this list of conditions and the following disclaimer in the | |
| // documentation and/or other materials provided with the distribution. | |
| // * Neither the name of the authors nor the names of its contributors | |
| // may be used to endorse or promote products derived from this software | |
| // without specific prior written permission. | |
| // | |
| // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
| // AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
| // IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE | |
| // ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE | |
| // LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, | |
| // OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF | |
| // SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS | |
| // INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN | |
| // CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) | |
| // ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF | |
| // THE POSSIBILITY OF SUCH DAMAGE | |
| // | |
| //---------------------------------------------------------------------------- | |
| // | |
| // *File Name: openMSP430.v | |
| // | |
| // *Module Description: | |
| // openMSP430 Top level file | |
| // | |
| // *Author(s): | |
| // - Olivier Girard, olgirard@gmail.com | |
| // | |
| //---------------------------------------------------------------------------- | |
| // $Rev: 175 $ | |
| // $LastChangedBy: olivier.girard $ | |
| // $LastChangedDate: 2013-01-30 22:21:42 +0100 (Wed, 30 Jan 2013) $ | |
| //---------------------------------------------------------------------------- | |
| `ifdef OMSP_NO_INCLUDE | |
| `else | |
| `include "openMSP430_defines.v" | |
| `endif | |
| module openMSP430 ( | |
| // OUTPUTs | |
| aclk, // ASIC ONLY: ACLK | |
| aclk_en, // FPGA ONLY: ACLK enable | |
| dbg_freeze, // Freeze peripherals | |
| dbg_i2c_sda_out, // Debug interface: I2C SDA OUT | |
| dbg_uart_txd, // Debug interface: UART TXD | |
| dco_enable, // ASIC ONLY: Fast oscillator enable | |
| dco_wkup, // ASIC ONLY: Fast oscillator wake-up (asynchronous) | |
| dmem_addr, // Data Memory address | |
| dmem_cen, // Data Memory chip enable (low active) | |
| dmem_din, // Data Memory data input | |
| dmem_wen, // Data Memory write enable (low active) | |
| irq_acc, // Interrupt request accepted (one-hot signal) | |
| lfxt_enable, // ASIC ONLY: Low frequency oscillator enable | |
| lfxt_wkup, // ASIC ONLY: Low frequency oscillator wake-up (asynchronous) | |
| mclk, // Main system clock | |
| per_addr, // Peripheral address | |
| per_din, // Peripheral data input | |
| per_we, // Peripheral write enable (high active) | |
| per_en, // Peripheral enable (high active) | |
| pmem_addr, // Program Memory address | |
| pmem_cen, // Program Memory chip enable (low active) | |
| pmem_din, // Program Memory data input (optional) | |
| pmem_wen, // Program Memory write enable (low active) (optional) | |
| puc_rst, // Main system reset | |
| smclk, // ASIC ONLY: SMCLK | |
| smclk_en, // FPGA ONLY: SMCLK enable | |
| // INPUTs | |
| cpu_en, // Enable CPU code execution (asynchronous and non-glitchy) | |
| dbg_en, // Debug interface enable (asynchronous and non-glitchy) | |
| dbg_i2c_addr, // Debug interface: I2C Address | |
| dbg_i2c_broadcast, // Debug interface: I2C Broadcast Address (for multicore systems) | |
| dbg_i2c_scl, // Debug interface: I2C SCL | |
| dbg_i2c_sda_in, // Debug interface: I2C SDA IN | |
| dbg_uart_rxd, // Debug interface: UART RXD (asynchronous) | |
| dco_clk, // Fast oscillator (fast clock) | |
| dmem_dout, // Data Memory data output | |
| irq, // Maskable interrupts | |
| lfxt_clk, // Low frequency oscillator (typ 32kHz) | |
| nmi, // Non-maskable interrupt (asynchronous) | |
| per_dout, // Peripheral data output | |
| pmem_dout, // Program Memory data output | |
| reset_n, // Reset Pin (low active, asynchronous and non-glitchy) | |
| scan_enable, // ASIC ONLY: Scan enable (active during scan shifting) | |
| scan_mode, // ASIC ONLY: Scan mode | |
| wkup // ASIC ONLY: System Wake-up (asynchronous and non-glitchy) | |
| ); | |
| // PARAMETERs | |
| //============ | |
| parameter INST_NR = 8'h00; // Current oMSP instance number (for multicore systems) | |
| parameter TOTAL_NR = 8'h00; // Total number of oMSP instances-1 (for multicore systems) | |
| // OUTPUTs | |
| //============ | |
| output aclk; // ASIC ONLY: ACLK | |
| output aclk_en; // FPGA ONLY: ACLK enable | |
| output dbg_freeze; // Freeze peripherals | |
| output dbg_i2c_sda_out; // Debug interface: I2C SDA OUT | |
| output dbg_uart_txd; // Debug interface: UART TXD | |
| output dco_enable; // ASIC ONLY: Fast oscillator enable | |
| output dco_wkup; // ASIC ONLY: Fast oscillator wake-up (asynchronous) | |
| output [`DMEM_MSB:0] dmem_addr; // Data Memory address | |
| output dmem_cen; // Data Memory chip enable (low active) | |
| output [15:0] dmem_din; // Data Memory data input | |
| output [1:0] dmem_wen; // Data Memory write enable (low active) | |
| output [13:0] irq_acc; // Interrupt request accepted (one-hot signal) | |
| output lfxt_enable; // ASIC ONLY: Low frequency oscillator enable | |
| output lfxt_wkup; // ASIC ONLY: Low frequency oscillator wake-up (asynchronous) | |
| output mclk; // Main system clock | |
| output [13:0] per_addr; // Peripheral address | |
| output [15:0] per_din; // Peripheral data input | |
| output [1:0] per_we; // Peripheral write enable (high active) | |
| output per_en; // Peripheral enable (high active) | |
| output [`PMEM_MSB:0] pmem_addr; // Program Memory address | |
| output pmem_cen; // Program Memory chip enable (low active) | |
| output [15:0] pmem_din; // Program Memory data input (optional) | |
| output [1:0] pmem_wen; // Program Memory write enable (low active) (optional) | |
| output puc_rst; // Main system reset | |
| output smclk; // ASIC ONLY: SMCLK | |
| output smclk_en; // FPGA ONLY: SMCLK enable | |
| // INPUTs | |
| //============ | |
| input cpu_en; // Enable CPU code execution (asynchronous and non-glitchy) | |
| input dbg_en; // Debug interface enable (asynchronous and non-glitchy) | |
| input [6:0] dbg_i2c_addr; // Debug interface: I2C Address | |
| input [6:0] dbg_i2c_broadcast; // Debug interface: I2C Broadcast Address (for multicore systems) | |
| input dbg_i2c_scl; // Debug interface: I2C SCL | |
| input dbg_i2c_sda_in; // Debug interface: I2C SDA IN | |
| input dbg_uart_rxd; // Debug interface: UART RXD (asynchronous) | |
| input dco_clk; // Fast oscillator (fast clock) | |
| input [15:0] dmem_dout; // Data Memory data output | |
| input [13:0] irq; // Maskable interrupts | |
| input lfxt_clk; // Low frequency oscillator (typ 32kHz) | |
| input nmi; // Non-maskable interrupt (asynchronous and non-glitchy) | |
| input [15:0] per_dout; // Peripheral data output | |
| input [15:0] pmem_dout; // Program Memory data output | |
| input reset_n; // Reset Pin (active low, asynchronous and non-glitchy) | |
| input scan_enable; // ASIC ONLY: Scan enable (active during scan shifting) | |
| input scan_mode; // ASIC ONLY: Scan mode | |
| input wkup; // ASIC ONLY: System Wake-up (asynchronous and non-glitchy) | |
| //============================================================================= | |
| // 1) INTERNAL WIRES/REGISTERS/PARAMETERS DECLARATION | |
| //============================================================================= | |
| wire [7:0] inst_ad; | |
| wire [7:0] inst_as; | |
| wire [11:0] inst_alu; | |
| wire inst_bw; | |
| wire inst_irq_rst; | |
| wire inst_mov; | |
| wire [15:0] inst_dest; | |
| wire [15:0] inst_dext; | |
| wire [15:0] inst_sext; | |
| wire [7:0] inst_so; | |
| wire [15:0] inst_src; | |
| wire [2:0] inst_type; | |
| wire [7:0] inst_jmp; | |
| wire [3:0] e_state; | |
| wire exec_done; | |
| wire decode_noirq; | |
| wire cpu_en_s; | |
| wire cpuoff; | |
| wire oscoff; | |
| wire scg0; | |
| wire scg1; | |
| wire por; | |
| wire gie; | |
| wire mclk_enable; | |
| wire mclk_wkup; | |
| wire [31:0] cpu_id; | |
| wire [7:0] cpu_nr_inst = INST_NR; | |
| wire [7:0] cpu_nr_total = TOTAL_NR; | |
| wire [15:0] eu_mab; | |
| wire [15:0] eu_mdb_in; | |
| wire [15:0] eu_mdb_out; | |
| wire [1:0] eu_mb_wr; | |
| wire eu_mb_en; | |
| wire [15:0] fe_mab; | |
| wire [15:0] fe_mdb_in; | |
| wire fe_mb_en; | |
| wire fe_pmem_wait; | |
| wire pc_sw_wr; | |
| wire [15:0] pc_sw; | |
| wire [15:0] pc; | |
| wire [15:0] pc_nxt; | |
| wire nmi_acc; | |
| wire nmi_pnd; | |
| wire nmi_wkup; | |
| wire wdtie; | |
| wire wdtnmies; | |
| wire wdtifg; | |
| wire wdt_irq; | |
| wire wdt_wkup; | |
| wire wdt_reset; | |
| wire wdtifg_sw_clr; | |
| wire wdtifg_sw_set; | |
| wire dbg_clk; | |
| wire dbg_rst; | |
| wire dbg_en_s; | |
| wire dbg_halt_st; | |
| wire dbg_halt_cmd; | |
| wire dbg_mem_en; | |
| wire dbg_reg_wr; | |
| wire dbg_cpu_reset; | |
| wire [15:0] dbg_mem_addr; | |
| wire [15:0] dbg_mem_dout; | |
| wire [15:0] dbg_mem_din; | |
| wire [15:0] dbg_reg_din; | |
| wire [1:0] dbg_mem_wr; | |
| wire puc_pnd_set; | |
| wire [15:0] per_dout_or; | |
| wire [15:0] per_dout_sfr; | |
| wire [15:0] per_dout_wdog; | |
| wire [15:0] per_dout_mpy; | |
| wire [15:0] per_dout_clk; | |
| //============================================================================= | |
| // 2) GLOBAL CLOCK & RESET MANAGEMENT | |
| //============================================================================= | |
| omsp_clock_module clock_module_0 ( | |
| // OUTPUTs | |
| .aclk (aclk), // ACLK | |
| .aclk_en (aclk_en), // ACLK enablex | |
| .cpu_en_s (cpu_en_s), // Enable CPU code execution (synchronous) | |
| .dbg_clk (dbg_clk), // Debug unit clock | |
| .dbg_en_s (dbg_en_s), // Debug interface enable (synchronous) | |
| .dbg_rst (dbg_rst), // Debug unit reset | |
| .dco_enable (dco_enable), // Fast oscillator enable | |
| .dco_wkup (dco_wkup), // Fast oscillator wake-up (asynchronous) | |
| .lfxt_enable (lfxt_enable), // Low frequency oscillator enable | |
| .lfxt_wkup (lfxt_wkup), // Low frequency oscillator wake-up (asynchronous) | |
| .mclk (mclk), // Main system clock | |
| .per_dout (per_dout_clk), // Peripheral data output | |
| .por (por), // Power-on reset | |
| .puc_pnd_set (puc_pnd_set), // PUC pending set for the serial debug interface | |
| .puc_rst (puc_rst), // Main system reset | |
| .smclk (smclk), // SMCLK | |
| .smclk_en (smclk_en), // SMCLK enable | |
| // INPUTs | |
| .cpu_en (cpu_en), // Enable CPU code execution (asynchronous) | |
| .cpuoff (cpuoff), // Turns off the CPU | |
| .dbg_cpu_reset(dbg_cpu_reset), // Reset CPU from debug interface | |
| .dbg_en (dbg_en), // Debug interface enable (asynchronous) | |
| .dco_clk (dco_clk), // Fast oscillator (fast clock) | |
| .lfxt_clk (lfxt_clk), // Low frequency oscillator (typ 32kHz) | |
| .mclk_enable (mclk_enable), // Main System Clock enable | |
| .mclk_wkup (mclk_wkup), // Main System Clock wake-up (asynchronous) | |
| .oscoff (oscoff), // Turns off LFXT1 clock input | |
| .per_addr (per_addr), // Peripheral address | |
| .per_din (per_din), // Peripheral data input | |
| .per_en (per_en), // Peripheral enable (high active) | |
| .per_we (per_we), // Peripheral write enable (high active) | |
| .reset_n (reset_n), // Reset Pin (low active, asynchronous) | |
| .scan_enable (scan_enable), // Scan enable (active during scan shifting) | |
| .scan_mode (scan_mode), // Scan mode | |
| .scg0 (scg0), // System clock generator 1. Turns off the DCO | |
| .scg1 (scg1), // System clock generator 1. Turns off the SMCLK | |
| .wdt_reset (wdt_reset) // Watchdog-timer reset | |
| ); | |
| //============================================================================= | |
| // 3) FRONTEND (<=> FETCH & DECODE) | |
| //============================================================================= | |
| omsp_frontend frontend_0 ( | |
| // OUTPUTs | |
| .dbg_halt_st (dbg_halt_st), // Halt/Run status from CPU | |
| .decode_noirq (decode_noirq), // Frontend decode instruction | |
| .e_state (e_state), // Execution state | |
| .exec_done (exec_done), // Execution completed | |
| .inst_ad (inst_ad), // Decoded Inst: destination addressing mode | |
| .inst_as (inst_as), // Decoded Inst: source addressing mode | |
| .inst_alu (inst_alu), // ALU control signals | |
| .inst_bw (inst_bw), // Decoded Inst: byte width | |
| .inst_dest (inst_dest), // Decoded Inst: destination (one hot) | |
| .inst_dext (inst_dext), // Decoded Inst: destination extended instruction word | |
| .inst_irq_rst (inst_irq_rst), // Decoded Inst: Reset interrupt | |
| .inst_jmp (inst_jmp), // Decoded Inst: Conditional jump | |
| .inst_mov (inst_mov), // Decoded Inst: mov instruction | |
| .inst_sext (inst_sext), // Decoded Inst: source extended instruction word | |
| .inst_so (inst_so), // Decoded Inst: Single-operand arithmetic | |
| .inst_src (inst_src), // Decoded Inst: source (one hot) | |
| .inst_type (inst_type), // Decoded Instruction type | |
| .irq_acc (irq_acc), // Interrupt request accepted | |
| .mab (fe_mab), // Frontend Memory address bus | |
| .mb_en (fe_mb_en), // Frontend Memory bus enable | |
| .mclk_enable (mclk_enable), // Main System Clock enable | |
| .mclk_wkup (mclk_wkup), // Main System Clock wake-up (asynchronous) | |
| .nmi_acc (nmi_acc), // Non-Maskable interrupt request accepted | |
| .pc (pc), // Program counter | |
| .pc_nxt (pc_nxt), // Next PC value (for CALL & IRQ) | |
| // INPUTs | |
| .cpu_en_s (cpu_en_s), // Enable CPU code execution (synchronous) | |
| .cpuoff (cpuoff), // Turns off the CPU | |
| .dbg_halt_cmd (dbg_halt_cmd), // Halt CPU command | |
| .dbg_reg_sel (dbg_mem_addr[3:0]), // Debug selected register for rd/wr access | |
| .fe_pmem_wait (fe_pmem_wait), // Frontend wait for Instruction fetch | |
| .gie (gie), // General interrupt enable | |
| .irq (irq), // Maskable interrupts | |
| .mclk (mclk), // Main system clock | |
| .mdb_in (fe_mdb_in), // Frontend Memory data bus input | |
| .nmi_pnd (nmi_pnd), // Non-maskable interrupt pending | |
| .nmi_wkup (nmi_wkup), // NMI Wakeup | |
| .pc_sw (pc_sw), // Program counter software value | |
| .pc_sw_wr (pc_sw_wr), // Program counter software write | |
| .puc_rst (puc_rst), // Main system reset | |
| .scan_enable (scan_enable), // Scan enable (active during scan shifting) | |
| .wdt_irq (wdt_irq), // Watchdog-timer interrupt | |
| .wdt_wkup (wdt_wkup), // Watchdog Wakeup | |
| .wkup (wkup) // System Wake-up (asynchronous) | |
| ); | |
| //============================================================================= | |
| // 4) EXECUTION UNIT | |
| //============================================================================= | |
| omsp_execution_unit execution_unit_0 ( | |
| // OUTPUTs | |
| .cpuoff (cpuoff), // Turns off the CPU | |
| .dbg_reg_din (dbg_reg_din), // Debug unit CPU register data input | |
| .mab (eu_mab), // Memory address bus | |
| .mb_en (eu_mb_en), // Memory bus enable | |
| .mb_wr (eu_mb_wr), // Memory bus write transfer | |
| .mdb_out (eu_mdb_out), // Memory data bus output | |
| .oscoff (oscoff), // Turns off LFXT1 clock input | |
| .pc_sw (pc_sw), // Program counter software value | |
| .pc_sw_wr (pc_sw_wr), // Program counter software write | |
| .scg0 (scg0), // System clock generator 1. Turns off the DCO | |
| .scg1 (scg1), // System clock generator 1. Turns off the SMCLK | |
| // INPUTs | |
| .dbg_halt_st (dbg_halt_st), // Halt/Run status from CPU | |
| .dbg_mem_dout (dbg_mem_dout), // Debug unit data output | |
| .dbg_reg_wr (dbg_reg_wr), // Debug unit CPU register write | |
| .e_state (e_state), // Execution state | |
| .exec_done (exec_done), // Execution completed | |
| .gie (gie), // General interrupt enable | |
| .inst_ad (inst_ad), // Decoded Inst: destination addressing mode | |
| .inst_as (inst_as), // Decoded Inst: source addressing mode | |
| .inst_alu (inst_alu), // ALU control signals | |
| .inst_bw (inst_bw), // Decoded Inst: byte width | |
| .inst_dest (inst_dest), // Decoded Inst: destination (one hot) | |
| .inst_dext (inst_dext), // Decoded Inst: destination extended instruction word | |
| .inst_irq_rst (inst_irq_rst), // Decoded Inst: reset interrupt | |
| .inst_jmp (inst_jmp), // Decoded Inst: Conditional jump | |
| .inst_mov (inst_mov), // Decoded Inst: mov instruction | |
| .inst_sext (inst_sext), // Decoded Inst: source extended instruction word | |
| .inst_so (inst_so), // Decoded Inst: Single-operand arithmetic | |
| .inst_src (inst_src), // Decoded Inst: source (one hot) | |
| .inst_type (inst_type), // Decoded Instruction type | |
| .mclk (mclk), // Main system clock | |
| .mdb_in (eu_mdb_in), // Memory data bus input | |
| .pc (pc), // Program counter | |
| .pc_nxt (pc_nxt), // Next PC value (for CALL & IRQ) | |
| .puc_rst (puc_rst), // Main system reset | |
| .scan_enable (scan_enable) // Scan enable (active during scan shifting) | |
| ); | |
| //============================================================================= | |
| // 5) MEMORY BACKBONE | |
| //============================================================================= | |
| omsp_mem_backbone mem_backbone_0 ( | |
| // OUTPUTs | |
| .dbg_mem_din (dbg_mem_din), // Debug unit Memory data input | |
| .dmem_addr (dmem_addr), // Data Memory address | |
| .dmem_cen (dmem_cen), // Data Memory chip enable (low active) | |
| .dmem_din (dmem_din), // Data Memory data input | |
| .dmem_wen (dmem_wen), // Data Memory write enable (low active) | |
| .eu_mdb_in (eu_mdb_in), // Execution Unit Memory data bus input | |
| .fe_mdb_in (fe_mdb_in), // Frontend Memory data bus input | |
| .fe_pmem_wait (fe_pmem_wait), // Frontend wait for Instruction fetch | |
| .per_addr (per_addr), // Peripheral address | |
| .per_din (per_din), // Peripheral data input | |
| .per_we (per_we), // Peripheral write enable (high active) | |
| .per_en (per_en), // Peripheral enable (high active) | |
| .pmem_addr (pmem_addr), // Program Memory address | |
| .pmem_cen (pmem_cen), // Program Memory chip enable (low active) | |
| .pmem_din (pmem_din), // Program Memory data input (optional) | |
| .pmem_wen (pmem_wen), // Program Memory write enable (low active) (optional) | |
| // INPUTs | |
| .dbg_halt_st (dbg_halt_st), // Halt/Run status from CPU | |
| .dbg_mem_addr (dbg_mem_addr), // Debug address for rd/wr access | |
| .dbg_mem_dout (dbg_mem_dout), // Debug unit data output | |
| .dbg_mem_en (dbg_mem_en), // Debug unit memory enable | |
| .dbg_mem_wr (dbg_mem_wr), // Debug unit memory write | |
| .dmem_dout (dmem_dout), // Data Memory data output | |
| .eu_mab (eu_mab[15:1]), // Execution Unit Memory address bus | |
| .eu_mb_en (eu_mb_en), // Execution Unit Memory bus enable | |
| .eu_mb_wr (eu_mb_wr), // Execution Unit Memory bus write transfer | |
| .eu_mdb_out (eu_mdb_out), // Execution Unit Memory data bus output | |
| .fe_mab (fe_mab[15:1]), // Frontend Memory address bus | |
| .fe_mb_en (fe_mb_en), // Frontend Memory bus enable | |
| .mclk (mclk), // Main system clock | |
| .per_dout (per_dout_or), // Peripheral data output | |
| .pmem_dout (pmem_dout), // Program Memory data output | |
| .puc_rst (puc_rst), // Main system reset | |
| .scan_enable (scan_enable) // Scan enable (active during scan shifting) | |
| ); | |
| //============================================================================= | |
| // 6) SPECIAL FUNCTION REGISTERS | |
| //============================================================================= | |
| omsp_sfr sfr_0 ( | |
| // OUTPUTs | |
| .cpu_id (cpu_id), // CPU ID | |
| .nmi_pnd (nmi_pnd), // NMI Pending | |
| .nmi_wkup (nmi_wkup), // NMI Wakeup | |
| .per_dout (per_dout_sfr), // Peripheral data output | |
| .wdtie (wdtie), // Watchdog-timer interrupt enable | |
| .wdtifg_sw_clr(wdtifg_sw_clr), // Watchdog-timer interrupt flag software clear | |
| .wdtifg_sw_set(wdtifg_sw_set), // Watchdog-timer interrupt flag software set | |
| // INPUTs | |
| .cpu_nr_inst (cpu_nr_inst), // Current oMSP instance number | |
| .cpu_nr_total (cpu_nr_total), // Total number of oMSP instances-1 | |
| .mclk (mclk), // Main system clock | |
| .nmi (nmi), // Non-maskable interrupt (asynchronous) | |
| .nmi_acc (nmi_acc), // Non-Maskable interrupt request accepted | |
| .per_addr (per_addr), // Peripheral address | |
| .per_din (per_din), // Peripheral data input | |
| .per_en (per_en), // Peripheral enable (high active) | |
| .per_we (per_we), // Peripheral write enable (high active) | |
| .puc_rst (puc_rst), // Main system reset | |
| .scan_mode (scan_mode), // Scan mode | |
| .wdtifg (wdtifg), // Watchdog-timer interrupt flag | |
| .wdtnmies (wdtnmies) // Watchdog-timer NMI edge selection | |
| ); | |
| //============================================================================= | |
| // 7) WATCHDOG TIMER | |
| //============================================================================= | |
| `ifdef WATCHDOG | |
| omsp_watchdog watchdog_0 ( | |
| // OUTPUTs | |
| .per_dout (per_dout_wdog), // Peripheral data output | |
| .wdt_irq (wdt_irq), // Watchdog-timer interrupt | |
| .wdt_reset (wdt_reset), // Watchdog-timer reset | |
| .wdt_wkup (wdt_wkup), // Watchdog Wakeup | |
| .wdtifg (wdtifg), // Watchdog-timer interrupt flag | |
| .wdtnmies (wdtnmies), // Watchdog-timer NMI edge selection | |
| // INPUTs | |
| .aclk (aclk), // ACLK | |
| .aclk_en (aclk_en), // ACLK enable | |
| .dbg_freeze (dbg_freeze), // Freeze Watchdog counter | |
| .mclk (mclk), // Main system clock | |
| .per_addr (per_addr), // Peripheral address | |
| .per_din (per_din), // Peripheral data input | |
| .per_en (per_en), // Peripheral enable (high active) | |
| .per_we (per_we), // Peripheral write enable (high active) | |
| .por (por), // Power-on reset | |
| .puc_rst (puc_rst), // Main system reset | |
| .scan_enable (scan_enable), // Scan enable (active during scan shifting) | |
| .scan_mode (scan_mode), // Scan mode | |
| .smclk (smclk), // SMCLK | |
| .smclk_en (smclk_en), // SMCLK enable | |
| .wdtie (wdtie), // Watchdog-timer interrupt enable | |
| .wdtifg_irq_clr (irq_acc[10]), // Clear Watchdog-timer interrupt flag | |
| .wdtifg_sw_clr (wdtifg_sw_clr), // Watchdog-timer interrupt flag software clear | |
| .wdtifg_sw_set (wdtifg_sw_set) // Watchdog-timer interrupt flag software set | |
| ); | |
| `else | |
| assign per_dout_wdog = 16'h0000; | |
| assign wdt_irq = 1'b0; | |
| assign wdt_reset = 1'b0; | |
| assign wdt_wkup = 1'b0; | |
| assign wdtifg = 1'b0; | |
| assign wdtnmies = 1'b0; | |
| `endif | |
| //============================================================================= | |
| // 8) HARDWARE MULTIPLIER | |
| //============================================================================= | |
| `ifdef MULTIPLIER | |
| omsp_multiplier multiplier_0 ( | |
| // OUTPUTs | |
| .per_dout (per_dout_mpy), // Peripheral data output | |
| // INPUTs | |
| .mclk (mclk), // Main system clock | |
| .per_addr (per_addr), // Peripheral address | |
| .per_din (per_din), // Peripheral data input | |
| .per_en (per_en), // Peripheral enable (high active) | |
| .per_we (per_we), // Peripheral write enable (high active) | |
| .puc_rst (puc_rst), // Main system reset | |
| .scan_enable (scan_enable) // Scan enable (active during scan shifting) | |
| ); | |
| `else | |
| assign per_dout_mpy = 16'h0000; | |
| `endif | |
| //============================================================================= | |
| // 9) PERIPHERALS' OUTPUT BUS | |
| //============================================================================= | |
| assign per_dout_or = per_dout | | |
| per_dout_clk | | |
| per_dout_sfr | | |
| per_dout_wdog | | |
| per_dout_mpy; | |
| //============================================================================= | |
| // 10) DEBUG INTERFACE | |
| //============================================================================= | |
| `ifdef DBG_EN | |
| omsp_dbg dbg_0 ( | |
| // OUTPUTs | |
| .dbg_cpu_reset (dbg_cpu_reset), // Reset CPU from debug interface | |
| .dbg_freeze (dbg_freeze), // Freeze peripherals | |
| .dbg_halt_cmd (dbg_halt_cmd), // Halt CPU command | |
| .dbg_i2c_sda_out (dbg_i2c_sda_out), // Debug interface: I2C SDA OUT | |
| .dbg_mem_addr (dbg_mem_addr), // Debug address for rd/wr access | |
| .dbg_mem_dout (dbg_mem_dout), // Debug unit data output | |
| .dbg_mem_en (dbg_mem_en), // Debug unit memory enable | |
| .dbg_mem_wr (dbg_mem_wr), // Debug unit memory write | |
| .dbg_reg_wr (dbg_reg_wr), // Debug unit CPU register write | |
| .dbg_uart_txd (dbg_uart_txd), // Debug interface: UART TXD | |
| // INPUTs | |
| .cpu_en_s (cpu_en_s), // Enable CPU code execution (synchronous) | |
| .cpu_id (cpu_id), // CPU ID | |
| .cpu_nr_inst (cpu_nr_inst), // Current oMSP instance number | |
| .cpu_nr_total (cpu_nr_total), // Total number of oMSP instances-1 | |
| .dbg_clk (dbg_clk), // Debug unit clock | |
| .dbg_en_s (dbg_en_s), // Debug interface enable (synchronous) | |
| .dbg_halt_st (dbg_halt_st), // Halt/Run status from CPU | |
| .dbg_i2c_addr (dbg_i2c_addr), // Debug interface: I2C Address | |
| .dbg_i2c_broadcast (dbg_i2c_broadcast), // Debug interface: I2C Broadcast Address (for multicore systems) | |
| .dbg_i2c_scl (dbg_i2c_scl), // Debug interface: I2C SCL | |
| .dbg_i2c_sda_in (dbg_i2c_sda_in), // Debug interface: I2C SDA IN | |
| .dbg_mem_din (dbg_mem_din), // Debug unit Memory data input | |
| .dbg_reg_din (dbg_reg_din), // Debug unit CPU register data input | |
| .dbg_rst (dbg_rst), // Debug unit reset | |
| .dbg_uart_rxd (dbg_uart_rxd), // Debug interface: UART RXD (asynchronous) | |
| .decode_noirq (decode_noirq), // Frontend decode instruction | |
| .eu_mab (eu_mab), // Execution-Unit Memory address bus | |
| .eu_mb_en (eu_mb_en), // Execution-Unit Memory bus enable | |
| .eu_mb_wr (eu_mb_wr), // Execution-Unit Memory bus write transfer | |
| .fe_mdb_in (fe_mdb_in), // Frontend Memory data bus input | |
| .pc (pc), // Program counter | |
| .puc_pnd_set (puc_pnd_set) // PUC pending set for the serial debug interface | |
| ); | |
| `else | |
| assign dbg_cpu_reset = 1'b0; | |
| assign dbg_freeze = ~cpu_en_s; | |
| assign dbg_halt_cmd = 1'b0; | |
| assign dbg_i2c_sda_out = 1'b1; | |
| assign dbg_mem_addr = 16'h0000; | |
| assign dbg_mem_dout = 16'h0000; | |
| assign dbg_mem_en = 1'b0; | |
| assign dbg_mem_wr = 2'b00; | |
| assign dbg_reg_wr = 1'b0; | |
| assign dbg_uart_txd = 1'b1; | |
| `endif | |
| endmodule // openMSP430 | |
| `ifdef OMSP_NO_INCLUDE | |
| `else | |
| `include "openMSP430_undefines.v" | |
| `endif |