| // | |
| // ------------------------------------------------------------- | |
| // Copyright 2011 Synopsys, Inc. | |
| // All Rights Reserved Worldwide | |
| // | |
| // Licensed under the Apache License, Version 2.0 (the | |
| // "License"); you may not use this file except in | |
| // compliance with the License. You may obtain a copy of | |
| // the License at | |
| // | |
| // http://www.apache.org/licenses/LICENSE-2.0 | |
| // | |
| // Unless required by applicable law or agreed to in | |
| // writing, software distributed under the License is | |
| // distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR | |
| // CONDITIONS OF ANY KIND, either express or implied. See | |
| // the License for the specific language governing | |
| // permissions and limitations under the License. | |
| // ------------------------------------------------------------- | |
| // | |
| This is an end-to-end phasing example involving a non-trivial | |
| (yet simple) DUT. | |
| 1. DUT SPECIFICATION | |
| The DUT is a full-duplex parallel-to-serial codec. | |
| Bytes written to the TxFIFO are transmitted MSB-first in order | |
| received. If there are no bytes to be transmitted, IDLE is | |
| transmitted. | |
| Received bytes are added to the RxFIFO if it is not full. SYNC, IDLE | |
| and ESC characters are ignored. | |
| The bit stream is identical in both direction. There is a SYNC | |
| character (0xB2) inserted every 7 bytes. IDLE characters (0x81) | |
| represent invalid data, unless escaped by a preceeding ESC character | |
| (0xE7). If an IDLE or ESC character must be transmitted as valid data, | |
| they must be preceeded by a ESC characted. The SYNC character, when | |
| found in a position other than the SYNC slot is a valid character. | |
| For example, the phrase 0xADB2EF81E7FEED could be transmitted as: | |
| B2 81 81 81 81 AD B2 B2 81 EF 81 E7 81 E7 B2 E7 81 E7 FE ED 81 B2 | |
| SS .. .. .. .. vv vv SS .. vv .. EE vv EE SS vv .. EE vv vv .. SS | |
| SS = SYNC | |
| EE = ESC | |
| .. = IDLE | |
| vv = Valid data | |
| Bits are valid at the rising edge of the clock. | |
| The following host-accessible registers are available: | |
| Address Bits Name | |
| 0x0000 IntSrc Interrupt Source | |
| RO 0:0 TxEmpty Tx FIFO is empty | |
| RO 1:1 TxLow Tx is at or below low water mark | |
| RO 2:2 TxFull Tx FIFO is full (32) | |
| RO 4:4 RxEmpty Rx FIFO is empty | |
| RO 5:5 RxHigh Rx FIFO is at or above high water mark | |
| RO 6:6 RxFull Rx FIFO is full (32) | |
| W1C 8:8 SA Symbol alignment has been acquired or lost | |
| Resets to 'b000010001 | |
| 0x0004 IntMask Interrupt Mask | |
| RW 8:0 If '0', masks the corresponding interrupt source | |
| Resets to all 0's | |
| 0x0010 TxStatus | |
| RW 0:0 TxEn Enable transmit path | |
| Resets to 0 | |
| 0x0014 TxLWM | |
| RW 4:0 TxLWM Low water mark for the Tx FIFO | |
| Resets to 8. | |
| 0x0020 RxStatus | |
| RW 0:0 RxEn Enable receive path | |
| RO 1:1 ALIGN Symbol alignment status | |
| Resets to all 0's | |
| 0x0024 RxHWM | |
| RW 4:0 RxHWM High water mark for the Rx FIFO | |
| Resets to 16. | |
| 0x0100 TxRx | |
| WO 7:0 TxData Write data to TxFIFO if not full | |
| RO 7:0 RxData Read data from RxFIFO if not empty | |
| All unspecified bits are RO and read at 0's. |