tests/various/peepopt.ys

read_verilog <<EOT
module peepopt_shiftmul_0 #(parameter N=3, parameter W=3) (input [N*W-1:0] i, input [$clog2(N)-1:0] s, output [W-1:0] o);
assign o = i[s*W+:W];
endmodule
EOT

prep -nokeepdc
equiv_opt -assert peepopt
design -load postopt
clean
select -assert-count 1 t:$shiftx
select -assert-count 0 t:$shiftx t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_shiftmul_1 (output [7:0] y, input [2:0] w);
assign y = 1'b1 >> (w * (3'b110));
endmodule
EOT

prep -nokeepdc
equiv_opt -assert peepopt
design -load postopt
clean
select -assert-count 1 t:$shr
select -assert-count 1 t:$mul
select -assert-count 0 t:$shr t:$mul %% t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_shiftmul_2 (input [11:0] D, input [1:0] S, output [11:0] Y);
	assign Y = D >> (S*3);
endmodule
EOT

prep
design -save gold
peepopt
design -stash gate

design -import gold -as gold peepopt_shiftmul_2
design -import gate -as gate peepopt_shiftmul_2

miter -equiv -make_assert -make_outputs -ignore_gold_x -flatten gold gate miter
sat -show-public -enable_undef -prove-asserts miter
cd gate
select -assert-count 1 t:$shr
select -assert-count 1 t:$mul
select -assert-count 0 t:$shr t:$mul %% t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_muldiv_0(input [1:0] i, output [1:0] o);
wire [3:0] t;
assign t = i * 3;
assign o = t / 3;
endmodule
EOT

prep -nokeepdc
equiv_opt -assert peepopt
design -load postopt
clean
select -assert-count 0 t:*

####################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_unsigned(input clk, ce, input [1:0] i, output reg [3:0] o);
    always @(posedge clk) if (ce) o <= i;
endmodule
EOT

proc
equiv_opt -assert peepopt
design -load postopt
clean
select -assert-count 1 t:$dff r:WIDTH=2 %i
select -assert-count 1 t:$mux r:WIDTH=2 %i
select -assert-count 0 t:$dff t:$mux %% t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_signed(input clk, ce, input signed [1:0] i, output reg signed [3:0] o);
    always @(posedge clk) if (ce) o <= i;
endmodule
EOT

proc
equiv_opt -assert peepopt
design -load postopt
clean
select -assert-count 1 t:$dff r:WIDTH=2 %i
select -assert-count 1 t:$mux r:WIDTH=2 %i
select -assert-count 0 t:$dff t:$mux %% t:* %D

###################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_const(input clk, ce, input [1:0] i, output reg [5:0] o);
    always @(posedge clk) if (ce) o <= {1'b0, i[1], 2'b1x, i[0], 1'bz};
endmodule
EOT

proc
equiv_opt -assert peepopt
design -load postopt
select -assert-count 1 t:$dff r:WIDTH=2 %i
select -assert-count 1 t:$mux r:WIDTH=2 %i
select -assert-count 0 t:$dff t:$mux %% t:* %D

###################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_const_init(input clk, ce, input [1:0] i, (* init=6'b0x00x1 *) output reg [5:0] o);
    always @(posedge clk) if (ce) o <= {1'b0, i[1], 2'b1x, i[0], 1'bz};
endmodule
EOT

proc
equiv_opt -assert peepopt
design -load postopt
select -assert-count 1 t:$dff r:WIDTH=4 %i
select -assert-count 1 t:$mux r:WIDTH=4 %i
select -assert-count 0 t:$dff t:$mux %% t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_unsigned_rst(input clk, ce, rst, input [1:0] i, output reg [3:0] o);
    always @(posedge clk) if (rst) o <= 0; else if (ce) o <= i;
endmodule
EOT

proc
equiv_opt -assert peepopt
design -load postopt
wreduce
select -assert-count 1 t:$dff r:WIDTH=2 %i
select -assert-count 2 t:$mux
select -assert-count 2 t:$mux r:WIDTH=2 %i
select -assert-count 0 t:$dff t:$mux %% t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_signed_rst(input clk, ce, rstn, input signed [1:0] i, output reg signed [3:0] o);
    always @(posedge clk) begin
        if (ce) o <= i;
        if (!rstn) o <= 4'b1111;
    end
endmodule
EOT

proc
equiv_opt -assert peepopt
design -load postopt
wreduce
select -assert-count 1 t:$dff r:WIDTH=2 %i
select -assert-count 2 t:$mux
select -assert-count 2 t:$mux r:WIDTH=2 %i
select -assert-count 0 t:$logic_not t:$dff t:$mux %% t:* %D

####################

design -reset
read_verilog <<EOT
module peepopt_dffmuxext_signed_rst_init(input clk, ce, rstn, input signed [1:0] i, output reg signed [3:0] o);
    initial o <= 4'b0010;
    always @(posedge clk) begin
        if (ce) o <= i;
        if (!rstn) o <= 4'b1111;
    end
endmodule
EOT

proc
# NB: equiv_opt uses equiv_induct which covers
#     only the induction half of temporal induction
#     --- missing the base-case half
#     This makes it akin to `sat -tempinduct-inductonly`
#     instead of `sat -tempinduct-baseonly` or
#     `sat -tempinduct` which is necessary for this
#     testcase
#equiv_opt -assert peepopt

design -save gold
peepopt
wreduce
design -stash gate
design -import gold -as gold
design -import gate -as gate
miter -equiv -flatten -make_assert -make_outputs gold gate miter
sat -tempinduct -verify -prove-asserts -show-ports miter

design -load gate
select -assert-count 1 t:$dff r:WIDTH=4 %i
select -assert-count 2 t:$mux
select -assert-count 2 t:$mux r:WIDTH=4 %i
select -assert-count 0 t:$logic_not t:$dff t:$mux %% t:* %D